RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: sapca
Showing results 1 to 14 of 14
Search took 0.45 seconds.
Forum: Futaba Radios Direct support forum
01-16-2008, 04:58 AM
Replies: 1
Views: 534
Posted By sapca

modeltransfer from 14MZ to 12FG ???

Hi,

Is it possible to transfer my models on the 14MZ to the 12FG ????

Regards

Sapca
Forum: Weatronic Support Forum
12-16-2007, 03:41 AM
Replies: 10
Views: 2,122
Posted By sapca

RE: Jitter with hitec 5955 servo

Hi Gerhard,

I did all the things you whrite,bud still have the same problem :-((

The point is,that when I use a futaba 149 DP receiver on a emcotec,everything is working fine.

So that...
Forum: Weatronic Support Forum
12-15-2007, 05:04 AM
Replies: 10
Views: 2,122
Posted By sapca

RE: Jitter with hitec 5955 servo

I use 2x 3700 mah flightpower lipo ( 7.4 V )

I was thinking that this is a factory support forum.

So the experts must be here.

regards

sapca
Forum: Weatronic Support Forum
12-15-2007, 03:36 AM
Replies: 10
Views: 2,122
Posted By sapca

RE: Jitter with hitec 5955 servo

Hi,
Now I did a test with a futaba FF9 TX on the weatronic,dud it makes NO difference

Than took back the 149 DP receiver on the FF9 and all servos working fine.

Regards

Sapca
Forum: Weatronic Support Forum
12-15-2007, 03:13 AM
Replies: 10
Views: 2,122
Posted By sapca

RE: Jitter with hitec 5955 servo

Hi,

I just did a new scan on a different freq,bud the problem is still tere.

regards

Sapca
Forum: Weatronic Support Forum
12-14-2007, 11:53 AM
Replies: 10
Views: 2,122
Posted By sapca

Jitter with hitec 5955 servo

Hi,

I use new hitec 5955 servo with the futaba 14MZ on the weatronic system.

When I slowly move elevator or rudder, my servos not moving smooth,they jitters.

Before I used a simple 149...
Forum: Weatronic Support Forum
11-15-2007, 12:02 PM
Replies: 6
Views: 1,215
Posted By sapca

RE: SD card question

Hi,

I have find a solution :-)))

When I push in the sd-card,I have to pull it a little up with my nail and than she locks .

Regards

Sapca
Forum: Weatronic Support Forum
11-13-2007, 12:09 PM
Replies: 6
Views: 1,215
Posted By sapca

RE: SD card question

Hi Gerhard,

I had Alwin Mueller on the phone this afternoon and he told me to sent in the receiver.

He is gone swap the RX to a new one.

That is what I call SERVICE.

Regards
Forum: Weatronic Support Forum
11-13-2007, 05:30 AM
Replies: 6
Views: 1,215
Posted By sapca

RE: SD card question

Why do I feel a tension off a sping when I push the card in.

normal did that mean that it is a push to latch, push to unlach slot.

Regards

sapca
Forum: Weatronic Support Forum
11-13-2007, 03:57 AM
Replies: 6
Views: 1,215
Posted By sapca

SD card question

Hi,

The SD card don't lock in the weatronic.

The card always come out.

??????

Regards
Forum: WildHare R/C Support
04-01-2007, 12:49 PM
Replies: 3
Views: 594
Posted By sapca

RE: sidetrust engine on WH edge V2

Thx silversurfer,

I only have 1,7 deg right thrust and 0,5 deg downtrust.

I don't have the long engine standoffs for the DA ,so I use shims and that give me the whrong right thrust.

...
Forum: WildHare R/C Support
03-31-2007, 02:32 AM
Replies: 3
Views: 594
Posted By sapca

sidetrust engine on WH edge V2

Hi Dudes,

What is the site and down or uptrust for the engine on the Wild-Hare Edge V2 ??

Regards

Sapca
Forum: WildHare R/C Support
02-17-2007, 06:50 AM
Replies: 590
Views: 73,968
Posted By sapca

RE: 50cc Edge V2 has landed

Hi,

In the manual there is notting abouth the CG.

Any sugestions ???

No I have make him level at 4,5 inch from the leading edge of the wing,bud the fueltank is in front of the CG and...
Forum: WildHare R/C Support
12-28-2006, 06:14 PM
Replies: 47
Views: 5,615
Posted By sapca

RE: New 50cc Wild Hare Edge coming Dec 2006

Hi Dudes,

How can I see that I have a V2 or a V1 EDGE 28%

Regards

Sapca
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.