RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mrorv
Showing results 1 to 17 of 17
Search took 0.73 seconds.
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-17-2004, 03:44 PM
Replies: 2
Views: 1,403
Posted By mrorv

digital servo whine

my hi-tec digital 5645 servos whine like a siren at times,WHY????? No experience with digitals so I might be doing something wrong. 4.8 V battery w/ either 2300 or 1700 mah. I'm using a6XFut pcmppm...
Forum: Giant Scale Aircraft - 3D & Aerobatic
10-02-2004, 03:28 AM
Replies: 0
Views: 480
Posted By mrorv

Lanier Laser 1/3 scale ARF

:eek:Directions say to mount rudder & elevator horns on the 1/4'' balsa sections. Shouldn't this be beefed up a bit by ply plates or ? Any suggestions would be deeply appreciated. 2 fellow flyers...
Forum: ARF or RTF
09-28-2004, 11:17 PM
Replies: 4
Views: 684
Posted By mrorv

RE: I've got some kind of radio glitch...

I had same problem with one of my planes and traced it to a faulty servo extension wire. A brand new one at that. End of problem.mrorv
Forum: Glow Engines
08-28-2004, 11:32 AM
Replies: 5
Views: 741
Posted By mrorv

SAITO 72

What is factory setting for low speed. Having a fit trying to adjust Saito 72 to run right. Runs fine to about half throttle and then dies trying to get full throttle. Almost new w/ about 2-3...
Forum: Seaplanes
08-22-2004, 08:05 PM
Replies: 5
Views: 1,515
Posted By mrorv

1/4 scale sig floats

I'm building 46" SIG floats and I was told they need to be fibreglassed for strength. What are some of my options and what has some others done in similar situations? I've went ahead in manual and...
Forum: Kit Building
08-02-2003, 08:00 PM
Replies: 6
Views: 999
Posted By mrorv

Internal layouts for Phaeton 90

I'm building P90 also and plan to put servos in wing. Putting in 20 oz. tank so had to open up former a little to accomodate size. Don't know yet whether to put 4 aileron or leave as is. I have a...
Forum: Kit Building
06-06-2003, 10:38 PM
Replies: 7
Views: 2,668
Posted By mrorv

hog dihedral

I've built 3 hogs with hardly any dihedral at all. I think one was about 1/2'' off the table on one side with the other wing half flat on the table. Engines have been from 60-108s. All have flown...
Forum: Kit Building
06-06-2003, 10:17 PM
Replies: 2
Views: 703
Posted By mrorv

ultimate

Sorry, I should have clarified the bipe is the Lanier ultimate.
Forum: Kit Building
06-06-2003, 01:10 PM
Replies: 2
Views: 703
Posted By mrorv

engine for ultimate bipe

I'm going to use an O.S. 160fx on the ultimate and it seems like my mount will be mounted too high on the firewall. Mounting a fibreglass cowl and haven't made final adjustments yet. Anybody else...
Forum: Questions and Answers
05-27-2003, 04:30 AM
Replies: 12
Views: 1,411
Posted By mrorv

moron this subject

Hey, did somebody just call me friggen moron..I just got two words for you pal...#$%@#$%#&^$@!
Forum: Questions and Answers
05-26-2003, 01:29 AM
Replies: 7
Views: 766
Posted By mrorv

Paint on Monokote

I used white primer (monokote) and then white monokote to get shine. If no steel wool use a 400 or close to it sandpaper. If your going to camoflague an ac forget the primer and just paint it.
Forum: Questions and Answers
05-26-2003, 01:13 AM
Replies: 6
Views: 959
Posted By mrorv

best hinge to use

Whats the best hinge to use on either a 60 or 120 size ac. I've always used Dubro plastic hinges but have had two ailerons rip out that were not toothpicked in. I'm building a Lanier pitts w/ 60''...
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-18-2003, 06:59 AM
Replies: 5
Views: 715
Posted By mrorv

starter batts

Used wheel chair batterys at battery shops , and at a good price. 10 or 15 dollars
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-14-2003, 07:35 AM
Replies: 9
Views: 1,086
Posted By mrorv

strange things a-happenin'

Had the same problem with servos not doing what they should and traced the problem to a bad servo extension in one side of the wing, a 12 incher. Thats my guess or like the other gent said the Y...
Forum: Questions and Answers
05-27-2002, 03:14 AM
Replies: 4
Views: 581
Posted By mrorv

flight characteristics

midwest 60 size p51 with a st90 just gets off the ground and rolls to the left and crashes. built to specs and balanced right,whats wrong?
Forum: ARF or RTF
05-05-2002, 10:01 PM
Replies: 69
Views: 11,970
Posted By mrorv

WARNING: GP 1/3 Pitts

my mistake, i thought the pitts was a kit build but not an arf. i would still buy plane, and I am not afilliated with maker of pitts.
Forum: ARF or RTF
05-05-2002, 09:56 PM
Replies: 69
Views: 11,970
Posted By mrorv

WARNING: GP 1/3 Pitts

I've only been in rc for 8yrs and i've been told if a joint looks like it might give, use epoxxy for stronger hold. i've been thinking about giant aeromaster or eq.for bigger biplane. I would not be...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.