RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Rumble
Showing results 1 to 18 of 18
Search took 0.67 seconds.
Forum: Giant Scale Aircraft - General
03-02-2011, 05:42 PM
Replies: 1
Views: 585
Posted By Rumble

1st 40% questionServo Leads?

Have started on my first 40%er. I have a couple of 1/3 scale under my belt so it not all totally new. My question concerns the length of servo extensions. With 1/3 scale birds standard 36"...
Forum: Gas Engines
01-21-2011, 05:46 PM
Replies: 6
Views: 1,457
Posted By Rumble

RE: Electronic Kill Switch

I could see a modified electronic kill switch that used a mechanical relay. The electronic kill switch would pull in a normally open relay. The relay would make the power connection to the...
Forum: Gas Engines
01-21-2011, 05:07 PM
Replies: 6
Views: 1,457
Posted By Rumble

Electronic Kill Switch

I have just installed an electronic kill switch on a 1/3 scale Edge 540. I have always just used a regular cut off switch for electronic ignitions so my question is: Should you use both a manual...
Forum: Batteries & Chargers
01-20-2011, 06:31 AM
Replies: 4
Views: 691
Posted By Rumble

RE: NIMH pack Age?

Well it seems like the opinion is these packs need to go! Thanks for all the helpful comments.
Forum: Batteries & Chargers
01-18-2011, 04:33 PM
Replies: 4
Views: 691
Posted By Rumble

NIMH pack Age?

Can anyone give me information on the lifespan of NIMH packs. I currently have a couple of packs that were stored for better than 4 years. The pack were originally used for approx. 1 year before...
Forum: Gas Engines
03-13-2006, 08:51 PM
Replies: 56
Views: 9,493
Posted By Rumble

RE: KROMA 100 or 3W 106

I noticed on the pictures of the Extra post above, it appears the engine is using two seperate igintion mods. Am I mistaken?
Forum: Giant Scale Aircraft - 3D & Aerobatic
08-10-2005, 11:04 AM
Replies: 9
Views: 3,226
Posted By Rumble

Foam Core vs. Built Up

Don't want to start a fight, but would like some honest Pros and Cons of Foam Core vs. Build Up wing construction. I am considering the purchase of a 40% edge or yak in the near future and am only...
Forum: ZDZ & RCS Support
04-14-2005, 09:32 PM
Replies: 2
Views: 735
Posted By Rumble

ZSZ 80 spark plug gap

Hi Mike,
Can you tell me the correct sparkplug gap for the ZDZ 80 single, please?

Thanks
Forum: Giant Scale Aircraft - 3D & Aerobatic
12-29-2004, 09:30 AM
Replies: 0
Views: 471
Posted By Rumble

Hanger 9 or Aeroworks Edge 540?

OK, I am not looking to start a brand loyalty fight here, but would like to get some honest feedback on which Edge 540 ARF is considered the better quality and flight performer? I have narrowed my...
Forum: JR Radio & Spektrum Radios
09-11-2004, 10:36 PM
Replies: 1
Views: 566
Posted By Rumble

Expo on Throttle with 8103

Hi Danny,
I understand there is a mix that can be set up on the 8103 to provide expo for the throttle channel. Are you familiar with this one and can you give some set up instructions? I want to...
Forum: Tips & Techniques
05-11-2004, 09:26 AM
Replies: 5
Views: 4,848
Posted By Rumble

Windshield Material?

Was wondering if anyone has suggestions for material to fashion a new windshield for a Pilots Model Decathalon. Original was destroyed by an airplane hating Labrador Retriever.

Thanks,
Rian...
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-21-2003, 09:58 PM
Replies: 20
Views: 1,887
Posted By Rumble

ZDZ80 and H9 Sukhoi---WOW!!!!!!!!!

Just had to tell someone how great this combination turned out for me. Have had the Sukhoi since last fall, and have been battling with a poor running engine(not ZDZ) the entire time. Was scared to...
Forum: Giant Scale Aircraft - 3D & Aerobatic
04-16-2003, 11:50 AM
Replies: 4
Views: 703
Posted By Rumble

H9 Sukhoi and DA100 ???

I have a H9 Sukhoi and would like to put a twin on it. Does anyone know if the DA 100 will fit inside the cowl without too much cutting. If not the DA then would also like to hear from anyone else...
Forum: Gas Engines
12-29-2002, 12:18 AM
Replies: 1
Views: 537
Posted By Rumble

Velocity Stack for Brisson 5.8?

I am having a problem with the mid range on a Brison 5.8. I have ordered and received a velocity stack from Brison; however the midrange only got worse. The engine is mounted on H9 Sukhoi and the...
Forum: Gas Engines
12-15-2002, 06:03 AM
Replies: 0
Views: 484
Posted By Rumble

In Cowl Airbox?

Looking for plans, drawings or pictures of an in cowl airbox. Need to add one to a Brison 5.8 with crappy mid range. Have tried the Brison Venturi stack but the problem got even worse. Any other...
Forum: Gas Engines
09-03-2002, 01:23 PM
Replies: 2
Views: 507
Posted By Rumble

What Size spinner adapter for Brison 5.8?

Thanks Ken,
The Brison I am purchasing has both the six bolt hub and the single bolt hub. The engine is about 5 years old so I will assume it should be the same 3/8 shaft.
Thank again

Rian
Forum: Gas Engines
09-03-2002, 01:47 AM
Replies: 2
Views: 507
Posted By Rumble

What Size spinner adapter for Brison 5.8?

I am awaiting the arrival of a Brison 5.8 for a new project and would like to order the spinner for this plane. Can anyone tell me the correct size for the spinner adapter??

Please email me if...
Forum: Crash & Rebuild
09-03-2002, 01:41 AM
Replies: 1
Views: 701
Posted By Rumble

Sig Wing modifications

Hi,
Send me an email direct and I will send pictures and description of how we modified the wing in my 2nd Sukhoi. This after the first exploded in flight. Modifications are simple and require...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.