RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: GKraemer
Showing results 1 to 13 of 13
Search took 0.65 seconds.
Forum: Thunder Tiger - Raptor 30, 50, 60, 90
08-14-2005, 09:53 PM
Replies: 8
Views: 1,001
Posted By GKraemer

RE: Homemade training gear

I used 1/2 inch hardwood dowels. If I remember right, I used 4 and zip tied them to the landing gear and a hula-hoop. Raptor 30 with a .36 didn't have any problems picking them up. I used an Enya...
Forum: 3D Electric Flying!
06-03-2004, 10:15 PM
Replies: 4
Views: 1,289
Posted By GKraemer

3D Power System Setup

I'm requesting help in determining what power system components are required for the CAP-232 from www.3dfoamy.com.
I'm new to electrics and I'm trying to use MotoCalc 7 to configure a...
Forum: Scratch Building, Aircraft Design, 3D/CAD
04-29-2004, 09:45 PM
Replies: 3
Views: 894
Posted By GKraemer

Weed Whacker Aircraft Plans

Where can I find plans for a airplane that uses a 25cc Homelite or a 31CC Ryobi 2 stroke weed whacker engine?

Thanks

Garry
Forum: Thunder Tiger - Raptor 30, 50, 60, 90
08-18-2003, 01:45 AM
Replies: 4
Views: 620
Posted By GKraemer

Raptor V1 Hover Setup

OOPs, I really meant throttle curve for stunt modes is 100, 75, 50, 75, and 100.
Forum: Thunder Tiger - Raptor 30, 50, 60, 90
08-17-2003, 02:27 AM
Replies: 4
Views: 620
Posted By GKraemer

Raptor V1 Hover Setup

I have a Raptor V1 with .36 TT. I can hover it and fly it around. I had a member of our club check my setup and he set it for +10 and -4 degrees of pitch and hover at 3/4 stick. Now I have started...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-27-2003, 10:57 AM
Replies: 1
Views: 435
Posted By GKraemer

Servos/Gyro

Yes. I have a JR Transmitter (PCM), JR PCM receiver, Futaba 401 gryo, and Futaba digital servo. I did have to trim the plastic tab off the Futaba connector to fit my JR receiver. My Raptor flies...
Forum: Engine Conversions
04-20-2003, 03:55 PM
Replies: 3
Views: 3,681
Posted By GKraemer

Walbro Glow Carb

I saw a thread for a Ryobi glow conversion using a Walbro WT-499 carb (Glow Zenoah G-23). I'd like to find a glow carb that is designed for engines in the 35-41cc range. I'm thinking the WT-499 ...
Forum: Engine Conversions
04-20-2003, 03:14 PM
Replies: 5
Views: 1,264
Posted By GKraemer

Carb outlet

I had the same question for my homelite.
The outlet can be run into the inlet using a "T" fitting or you can just let it like it is. When you push the primer bulb, it will fill and if you keep...
Forum: Engine Conversions
04-20-2003, 03:08 PM
Replies: 48
Views: 10,575
Posted By GKraemer

WT 499 Carb

Volfy,

I'm interested in converting a Ryobi to glow. I see you used a WT 499 carb from a 23cc Zenoah. Do you have any idea how I can find the Walbro number of a carb designed for glow (methanol)...
Forum: Glow Engines
04-17-2003, 02:40 AM
Replies: 3
Views: 691
Posted By GKraemer

Magnum 1.20 2 Stroke (Version 1)

Anyone running a Magnum 1.20 2 stroke engine?
I'd like to know:
1 The operating RPM range.
2. And inherent problems? Weak crank, etc?
3. What's the difference between version I and version II...
Forum: Glow Engines
08-27-2002, 01:29 PM
Replies: 9
Views: 901
Posted By GKraemer

OS 46FX Cylinder

The problem is the liner is peeling away. The engine was purchased from another individual and I don't know much about it's history.

Garry
Forum: Glow Engines
08-25-2002, 08:49 PM
Replies: 9
Views: 901
Posted By GKraemer

OS 46FX Cylinder

Are there any third party sources for replacement cylinders for the OS 46 FX engine. 65+ seems high when a brand new engine sells for 109.00.

Thanks

Garry
Forum: Gas Engines
08-19-2002, 12:14 AM
Replies: 3
Views: 626
Posted By GKraemer

US Engines 41CC Muffler Problems

Anyone else having problems with the newly desinged muffler on the US Engines 41CC?

After flying 3 flights on a NEW engine the muffler was loose. Here is what I found:
1. The aluminum muffler...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.