RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Norm from oz
Showing results 1 to 25 of 25
Search took 0.67 seconds.
Forum: RC Helicopter Beginners Forum
11-01-2005, 06:28 PM
Replies: 1
Views: 1,020
Posted By Norm from oz

Question about gyro mounting tape

Is gyro mounting tape anything special, or just double sided foam sticky tape?
Forum: Kyosho Helicopters
09-23-2005, 10:52 AM
Replies: 1
Views: 490
Posted By Norm from oz

do the nexus 30 and 46 have same head?

Have a chance to purchase a nexus 46 at a very reasonable price with a nexus 30 as spares, are all the parts compatible?
Forum: RC Pattern Flying
02-07-2005, 06:05 PM
Replies: 167
Views: 42,293
Posted By Norm from oz

RE: CMPRO LEO 110

Hi Greg,

This is the only reference to "running a moki with a cline regulator" that I have come across.

http://webpages.charter.net/rcfu/KitReviews/MWGiles202.html

Norm
Forum: Giant Scale Aircraft - 3D & Aerobatic
04-18-2004, 04:15 AM
Replies: 2
Views: 285
Posted By Norm from oz

suggested side and downthrust on 92" extra

Could anyone with some experience in giant scale give me some suggested engine side and down thrust for a 92' extra with 3w 75 motor and 24*10 prop that I am scratch building?
Forum: ARF or RTF
10-30-2003, 09:23 AM
Replies: 1
Views: 570
Posted By Norm from oz

world models tai ji 40 cg

help,

I have been given a crashed World Models 'tai ji 40'
after much reconstruction this bird is ready to fly again.
I need the cg position to set it up

Can someone help??

thanks...
Forum: RC Pattern Flying
10-30-2003, 01:58 AM
Replies: 1
Views: 604
Posted By Norm from oz

balance point for world models-tai ji 40

Hi
I have been given a crashed tai ji 40.
After many weeks of rebuilding it is now ready to fly.
(almost)
Can someone tell me the balance point for this model.

Thanks fellas
Forum: 3D Flying!
12-07-2002, 11:12 AM
Replies: 31
Views: 2,259
Posted By Norm from oz

What is 3d??

Can someone tell me if this would be an OK 3d plane ??
I have a 3w 75 and need a plane to glue it to.

http://www.modeldesign.com.au/Extra330S.html

norm
Forum: 3D Flying!
12-07-2002, 02:45 AM
Replies: 31
Views: 2,259
Posted By Norm from oz

What is 3d??

thanks rcflyer86

that looks like one big challenge!!

Next question -- does it take a special plane to do 3d??
and what are the differences to other aerobatic planes like a pattern plane for...
Forum: 3D Flying!
12-07-2002, 02:09 AM
Replies: 31
Views: 2,259
Posted By Norm from oz

What is 3d??

Hi guys,
I have come across the term 3d several times in r/c magazines, but no explanation on what type of flying it is?

Can someone describe what 3d is all about??

norm
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
09-16-2002, 01:15 PM
Replies: 1
Views: 488
Posted By Norm from oz

90" Seafury which servo(s)

Hi Mike,
This is my first large scale model and would like some information on servos.
I am building a 90" Seafury with a 3w 75 motor, the finished model will weigh approx 12-14 kegs (26-30lbs)
I...
Forum: Giant Scale Aircraft - 3D & Aerobatic
09-15-2002, 03:41 AM
Replies: 0
Views: 618
Posted By Norm from oz

hitec hs 700bb for 90" seafury is this servo ok

Hi guys,

anybody out there using hitec 700bb for their bigger planes??
Is this an OK and reliable servo??
All good and bad experiences wanted.

norm
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-14-2002, 02:13 PM
Replies: 0
Views: 746
Posted By Norm from oz

hitec hs 700bb for 90" seafury is this servo ok

Hi guys,

anybody out there using hitec 700bb for their bigger planes??
Is this an OK and reliable servo??
All good and bad experiences wanted.

norm
Forum: Gas Engines
09-03-2002, 12:07 PM
Replies: 1
Views: 1,421
Posted By Norm from oz

Information on 3w 75 powermaster motor

I have aquired a nib 3w75 without instructions, can someone email me a copy of the running in procedure and general instructions that come with the motor.
Forum: Giant Scale Aircraft - 3D & Aerobatic
09-03-2002, 11:51 AM
Replies: 1
Views: 416
Posted By Norm from oz

New to giant scale, any and all advise greatly accepted

I have just picked up a 90 inch sea fury kit by 'MODEL DESIGN' with foam wings and fiberglass fuselage.

Here is there web address
http://www.modeldesign.com.au/

I have never built a glass and...
Forum: Glow Engines
08-25-2002, 11:27 PM
Replies: 15
Views: 1,158
Posted By Norm from oz

cam timing OS 90 fs

thanks jim
Forum: Glow Engines
08-25-2002, 02:38 PM
Replies: 15
Views: 1,158
Posted By Norm from oz

cam timing OS 90 fs

I have acquired an old 'OS 90 fs' and it is in reasonable condition except for the bearings, they have rust in them and needed replacing.

Can anyone tell me the correct reassembly procedures to...
Forum: O.S. Engines Support
08-25-2002, 02:29 PM
Replies: 2
Views: 563
Posted By Norm from oz

os 90 fs

I have acquired an old 'OS 90 fs' and it is in reasonable condition except for the bearings, they have rust in them and needed replacing.

Can you tell me the correct reassembly procedures to get...
Forum: Glow Engines
08-06-2002, 09:12 AM
Replies: 5
Views: 729
Posted By Norm from oz

how much

Ask if anyone in your club has a lathe.
I have straightened a couple of crankshafts for fellow members for nothing.
Some are repairable some are not, there will be someone in your club who will be...
Forum: Kit Building
08-05-2002, 01:35 AM
Replies: 3
Views: 901
Posted By Norm from oz

carl goldberg sukhoi

Thanks gentlemen

Norm
Forum: Kit Building
08-03-2002, 06:05 AM
Replies: 3
Views: 901
Posted By Norm from oz

carl goldberg sukhoi

Can anyone tell me if there is a maker or supplier of a fiberglass cowl for the 72 inch sukhoi in AUSTRALIA????
Forum: Glow Engines
07-25-2002, 01:49 PM
Replies: 21
Views: 2,224
Posted By Norm from oz

saito blew apart

The engine has been disassembled and it has not dropped a valve!

the piston, liner and top-end are perfect.

The con-rod is not bent.

The bearings are both free and feel good.

There is no...
Forum: Glow Engines
07-25-2002, 08:14 AM
Replies: 21
Views: 2,224
Posted By Norm from oz

saito blew apart

Today I saw a saito 150 blow apart while being flown.

The pilot was not revving it hard or abusing it in any way.
The motor went bang and pieces flew off it.
When the model was landed the motor...
Forum: Kit Building
07-15-2002, 02:13 AM
Replies: 12
Views: 1,788
Posted By Norm from oz

how many PIPER "?" kits are available

Can anyone tell me what planes PIPER made???
And what scale kits are available and from whom?
Preferably in the 40-60 size kits

thanks gentlemen.
norm
Forum: RC Fuels
06-20-2002, 10:59 PM
Replies: 7
Views: 2,138
Posted By Norm from oz

Methonal, Nitro and Klotz oil

If you were a bit closer to west oz I would be interested!!
Klotz oil is $aus80 for 3.8 ltrs(1us gallon) here.
and nitro is $aus100 for 3.8 ltrs
Forum: RC Fuels
06-20-2002, 04:12 AM
Replies: 8
Views: 2,557
Posted By Norm from oz

ethanol instead of methanol

Good morning gentlemen.

A question for the chemists in our group.
Could ethanol replace the methanol in glow fuel?
Would there be a catalytic reaction between the glow plug wire and ethanol?
I...
Showing results 1 to 25 of 25


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.