RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: Buzz1
Showing results 1 to 25 of 62
Search took 0.39 seconds.
Forum: Traxxas Monster Truck forum
05-10-2008, 03:18 PM
Replies: 12
Views: 794
Posted By Buzz1

RE: Clutch shimming

Definitely keep the washers between the shoes and flywheel. If the shoe/CB rubbing is not affecting performance or eating parts, go with it. I've run clutchnuts with and without grooves and have had...
Forum: Traxxas Monster Truck forum
05-10-2008, 01:34 PM
Replies: 12
Views: 794
Posted By Buzz1

RE: Clutch shimming

Placing washers between the shoes and flywheels is correct, especially with aluminum shoes. Plastic/teflon/composite/whatever type shoes don't gall against the flywheel and hang up as badly, but...
Forum: Traxxas Monster Truck forum
05-10-2008, 03:24 AM
Replies: 8
Views: 522
Posted By Buzz1

RE: what do you guys thank about this?

That long intake pipe between the filter and the carb will limit the amount of air the engine can draw in. The surface friction of the pipe walls acting on the air flow is a significant restriction. ...
Forum: Traxxas Monster Truck forum
03-02-2008, 12:23 AM
Replies: 12
Views: 639
Posted By Buzz1

RE: engine mount question?

You can run diff oil in only one axle if you want to until you get the itch to open the front diff and fill it with oil.

The whole point of running diff oil over grease is to tune how the diffs...
Forum: Traxxas Monster Truck forum
03-01-2008, 03:36 PM
Replies: 12
Views: 639
Posted By Buzz1

RE: engine mount question?

From the box, Revo diffs come with the grease you found in yours. The diffs have all the seals in place already and are set-up to run with silicon oil, so all you have to do is take them apart, clean...
Forum: Traxxas Monster Truck forum
12-02-2007, 02:26 AM
Replies: 34
Views: 2,296
Posted By Buzz1

RE: Is it true tht traxxas engines last only 5 gallons ?...

Any mechanical device can fail at any time for one of any of a thousand reasons, most of which you will never be able to decipher without a laboratory and a few dudes in white coats. Handy, since I...
Forum: Traxxas Monster Truck forum
12-02-2007, 02:11 AM
Replies: 20
Views: 1,887
Posted By Buzz1

RE: Truck wont coast

Check the clutch. Sounds like it's not disengaging.
Forum: Traxxas Monster Truck forum
10-14-2007, 09:29 PM
Replies: 2
Views: 531
Posted By Buzz1

RE: Slipper Clutch Upgrades

Or conversely, you are running the slipper too loose and the slipping is causing friction and heating up the spur gear, melting it. Whatever it is set at now, try going the other way and see what...
Forum: Traxxas Monster Truck forum
10-14-2007, 09:26 PM
Replies: 6
Views: 703
Posted By Buzz1

RE: aluminum or stock

Hey 89ram, about those clutch shoes you run...

I went in blind and clueless and bought a set of ofna 10013's for my sts 30. They are 1.7g, I am guessing the ones you use are different weight,...
Forum: Traxxas Monster Truck forum
10-12-2007, 12:02 AM
Replies: 19
Views: 1,056
Posted By Buzz1

RE: o no!!!!

Glowplug threads are 1/4x32 tpi.
Forum: Traxxas Monster Truck forum
10-07-2007, 12:01 AM
Replies: 18
Views: 1,161
Posted By Buzz1

RE: cool air = more power

You're a patient, patient man, Dave. ;)

Good on ya.:D
Forum: Traxxas Monster Truck forum
10-02-2007, 07:10 PM
Replies: 86
Views: 4,166
Posted By Buzz1

RE: STS .30

Aaahh, I see now. Thanx for the pic.

I'm going to try the Traxxas mount first, since I have it already, so I'll see if I have clearance problems with it and the pressure fitting.

I just got...
Forum: Traxxas Monster Truck forum
10-02-2007, 01:31 PM
Replies: 86
Views: 4,166
Posted By Buzz1

RE: STS .30

Hey Jeff, nice truck.

About your install....

Double pipe springs from the engine to the header? Is that thing belching hard enough to blow the header off?

Did you cut the header just...
Forum: Traxxas Monster Truck forum
09-30-2007, 09:43 PM
Replies: 86
Views: 4,166
Posted By Buzz1

RE: STS .30

I'm putting my STS in my Revo 3.3. I bought it Sept 8, before the buck took off, but even then, the exchange rate wasn't too bad. And it will take awhile for the prices to equalize (if they actually...
Forum: Traxxas Monster Truck forum
09-30-2007, 02:37 AM
Replies: 4
Views: 1,566
Posted By Buzz1

RE: refilling piggyback shocks??

You really need to work the shaft/piston and hold the shock at various angles to get the air into places you can bleed it out, both at the shock body cap and at the cap on the reservoir to get it...
Forum: Traxxas Monster Truck forum
09-30-2007, 02:26 AM
Replies: 86
Views: 4,166
Posted By Buzz1

RE: STS .30

My STS 30 and 702 pipe showed up at my door last Thursday, cost me $210 with shipping, a Traxxas BB mount (I needed a foc anyways) cost me $50, and I expect to buy some Techno ext. wheelbase arms for...
Forum: Traxxas Monster Truck forum
09-23-2007, 04:25 AM
Replies: 3
Views: 608
Posted By Buzz1

RE: Revo Pitch

Module 1.0 is the correct terminology for the stock Revo spur gear pitch. Metric 1.0... mod 1.0 ... all the same thing.
Forum: Traxxas Monster Truck forum
09-22-2007, 01:47 AM
Replies: 3
Views: 608
Posted By Buzz1

RE: Revo Pitch

It's metric 1.0.
Forum: Traxxas Monster Truck forum
09-18-2007, 01:28 AM
Replies: 19
Views: 1,279
Posted By Buzz1

RE: Revo owners...

A spacer plate between the bulkheads would look trick, no doubt, but the spacer rods would be worlds easier, just for testing if no other reason. Once you get it set-up the way you like, you could...
Forum: Traxxas Monster Truck forum
09-16-2007, 10:03 PM
Replies: 19
Views: 1,279
Posted By Buzz1

RE: Revo owners...

If you're just running skis and there's no diffs or driveshafts to worry about, you can split the front bulkheads as far apart as you like. You would need some sort of spacer/brace to take up the...
Forum: Traxxas Monster Truck forum
09-16-2007, 09:45 PM
Replies: 32
Views: 4,442
Posted By Buzz1

RE: Tekno RC E-Maxx wing mount. Will I be dissapointed?

Here's a Techno mount with pushrod brace mod on a Revo. No speaka da Maxx, so I have no idea how it mounts, but with a little looking around, you should be able to find a set of turnbuckles the right...
Forum: Traxxas Monster Truck forum
09-16-2007, 09:28 PM
Replies: 6
Views: 665
Posted By Buzz1

RE: os18tm pull start

You might be able to save some money right now if you found out why the ez start motor keeps falling off. Did you strip the screws or threads in the electric motor? Do they just back out? A couple of...
Forum: Traxxas Monster Truck forum
09-16-2007, 03:12 PM
Replies: 2
Views: 562
Posted By Buzz1

RE: nova clutch shoes

Heavier shoes will engage at a lower RPM, and that engagement will have less 'kick'. A lighter spring does the same thing.

Lighter shoes will engage at a higher RPM, allowing the engine to be...
Forum: Traxxas Monster Truck forum
09-15-2007, 10:25 PM
Replies: 20
Views: 1,760
Posted By Buzz1

RE: How to Install the STS 30M Motor

[>:]He he he, that's cool. I can't wait......[>:]

:D
Forum: Traxxas Monster Truck forum
09-15-2007, 02:07 AM
Replies: 30
Views: 1,541
Posted By Buzz1

RE: Lets play a guessing game...

There's you're problem right there.
Showing results 1 to 25 of 62
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.