RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 3DRokie
Showing results 1 to 14 of 14
Search took 0.66 seconds.
Forum: Futaba Radios Direct support forum
01-06-2021, 07:51 AM
Replies: 8
Views: 1,747
Posted By 3DRokie

Hi Bill, just a quick update for your...

Hi Bill, just a quick update for your information. Upon inspection by the Futaba service center my transmitter showed signs of a bad contact in the motherboard. When it was replaced all sporadic...
Forum: Futaba Radios Direct support forum
08-26-2020, 08:43 AM
Replies: 8
Views: 1,747
Posted By 3DRokie

Thank you, I will check the settings when I get...

Thank you, I will check the settings when I get the transmitter back from the Futaba service center. I had sent it in for an unrelated ‘RF module broken’ error I would get on initial startup of the...
Forum: Futaba Radios Direct support forum
08-25-2020, 12:57 AM
Replies: 8
Views: 1,747
Posted By 3DRokie

In both cases the transmitter was left on the...

In both cases the transmitter was left on the grass untouched for more than 5-10 minutes (I was talking to people). However, I had always assume that the shut-down would be a complete shut down. Is...
Forum: Futaba Radios Direct support forum
08-24-2020, 08:17 AM
Replies: 8
Views: 1,747
Posted By 3DRokie

It is a 18SZ

It is a 18SZ
Forum: Futaba Radios Direct support forum
08-24-2020, 04:19 AM
Replies: 8
Views: 1,747
Posted By 3DRokie

Help troubleshooting

Hi,

Flying a new plane for the first time yesterday I had two instances on the same day of a short term loss of response from the system. Luckily both times on the ground.

Plane is a wood...
Forum: Futaba Radios Direct support forum
07-16-2020, 06:11 AM
Replies: 2
Views: 1,196
Posted By 3DRokie

Ok, thanks for letting me know.

Ok, thanks for letting me know.
Forum: Futaba Radios Direct support forum
07-16-2020, 06:10 AM
Replies: 2
Views: 1,480
Posted By 3DRokie

Thank you!

Thank you!
Forum: Futaba Radios Direct support forum
07-16-2020, 05:42 AM
Replies: 2
Views: 1,196
Posted By 3DRokie

Upgrade R6308SBT to R7008sb?

As I will be reaching out to my local Futaba support soon, I was curious: can the Futaba R6308SBT be upgraded via software to the R7008SB?
Forum: Futaba Radios Direct support forum
07-16-2020, 05:35 AM
Replies: 2
Views: 1,480
Posted By 3DRokie

Power supply to most Futaba receivers

Can I safely use the SBUS and SBUS2 ports as my power input (with our without y-cable) if I am not using them?
I have been doing so, but I could not find any information about it in the...
Forum: Futaba Radios Direct support forum
07-15-2020, 03:53 AM
Replies: 11
Views: 4,358
Posted By 3DRokie

I think that model matching is definitely a good...

I think that model matching is definitely a good safety feature. However, I also keep more than one version of a program for a single plane based on different configurations.
Could Futaba please...
Forum: Futaba Radios Direct support forum
07-13-2020, 10:25 AM
Replies: 4
Views: 939
Posted By 3DRokie

Ok, thank you. I took it apart and can confirm it...

Ok, thank you. I took it apart and can confirm it seems to have some play for the pot to lever interface. The slider system looks a bit cheap and plasticky. I will take it to my service centre as I...
Forum: Futaba Radios Direct support forum
07-13-2020, 03:45 AM
Replies: 4
Views: 939
Posted By 3DRokie

Correct, I get a beep when it is at the center,...

Correct, I get a beep when it is at the center, but the notch that holds it in the center is at around 5-6%. It also has some play, so it has a 1-2% range where the notch holds it. Thanks, Dan
Forum: Futaba Radios Direct support forum
07-12-2020, 09:32 AM
Replies: 4
Views: 939
Posted By 3DRokie

18sz Right Slider not centering

Hello,

Recently my 18SZ right slider (RS) has lost it's center. I have tried tightening the slider tension screw and this now stabilizes the slider at 4% off center reasonably consistently....
Forum: Park Flyers & Backyard Flyers
10-16-2002, 01:27 PM
Replies: 3
Views: 1,300
Posted By 3DRokie

Diablotin Super & Hacker Motor

Hi!

I am also in the process of putting together a Super Diablotin. I was thinking about using a HackerB50 Motor as well. Could anyone give me any hints about the setup and motor details.
Do I...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.