RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ARP35
Showing results 1 to 22 of 22
Search took 0.64 seconds.
Forum: RC Car General Discussions
08-06-2003, 02:05 PM
Replies: 5
Views: 2,576
Posted By ARP35

OFNA Starter box "wheel" doesn't fit in chassis

Thanks for all the replies. After researching, I discovered that unless I do what I8tweety says it won't work. A larger flywheel could work but it would be expensive and time consuming to get it...
Forum: RC Car General Discussions
07-29-2003, 06:32 PM
Replies: 5
Views: 2,576
Posted By ARP35

OFNA Starter box "wheel" doesn't fit in chassis

Need suggestions...I have a 1/8 Mirage V-Spec buggy. I just purchased an OFNA starter box (the blue one with chrome top). Anyway, the rubber wheel will not contact the engine flywheel. The opening...
Forum: RC Helicopter General Discussions
06-10-2003, 12:12 PM
Replies: 2
Views: 480
Posted By ARP35

Venture Clutch bell question?

Thanks....
Forum: RC Helicopter General Discussions
06-09-2003, 02:47 PM
Replies: 2
Views: 480
Posted By ARP35

Venture Clutch bell question?

Hi,
I had to reverse the OS 32 engine in the mounting block because it would not fit the way the manual describes. I think the manual is wrong. Anyway with the motor pulled out I noticed the...
Forum: RC Helicopter General Discussions
06-08-2003, 05:15 PM
Replies: 5
Views: 489
Posted By ARP35

radio xp662 question

When you are in the programing section on the travel adjustment screen, you can adjust the values from -150% to +150% for throttle, pitch, aileron, and elevator. For example, if in the throttle ATV...
Forum: RC Helicopter General Discussions
06-06-2003, 01:50 PM
Replies: 5
Views: 489
Posted By ARP35

radio xp662 question

I am not sure what you are trying to set. If it is the travel adjustment ATV for the Aileron, Elevator, Pitch, then you have to move the sticks on the tx to see the +- values. Be more specific if...
Forum: RC Helicopter Beginners Forum
06-06-2003, 01:24 PM
Replies: 4
Views: 600
Posted By ARP35

Blade pitch differences???

Thanks for the replies... I think I have everything set up correctly so I'll attempt a hover this weekend. I matched the blades pitch, seesaw arms are parallel, pitch curve is 0, 5, 9, servo arms...
Forum: RC Helicopter Beginners Forum
06-05-2003, 05:26 PM
Replies: 4
Views: 600
Posted By ARP35

Blade pitch differences???

Hi all,
I am setting up a Venture and was checking the pitch angle on the blades. I'm using a Helimax guage. The pitch angle on one blade is 2 or 3 degrees different then the other blade. The...
Forum: RC Boats General Discussion
05-09-2003, 02:52 PM
Replies: 3
Views: 571
Posted By ARP35

New Boat owner???

bump
Forum: RC Boats General Discussion
05-08-2003, 02:28 PM
Replies: 3
Views: 571
Posted By ARP35

New Boat owner???

Hi,
I just purchased (for my son) a Freedom RZ boat with the Dynamite .15S water-cooled engine and a JR XR2i radio for a birthday present. I have been flying airplanes for a while but new to the...
Forum: Beginners
02-28-2003, 07:11 PM
Replies: 54
Views: 4,758
Posted By ARP35

(wow) What The #@$*

I had a good laugh at all the stories and then remembered one of my own...
I was building my first trainer and needless to say the instructions were weak. Anyway, I got to the part about hinging...
Forum: Electric Training
01-25-2003, 04:50 PM
Replies: 4
Views: 729
Posted By ARP35

Radio setup question?

Thanks for the quick replies...I just needed reassurance I was breaking some unknown rule.
Forum: Electric Training
01-24-2003, 09:52 PM
Replies: 4
Views: 729
Posted By ARP35

Radio setup question?

Hi,
I am new to electrics...I have a GWS slowstick FD and am wondering if i could connect the rudder servo to the aileron connector on the receiver. This way I could use the aileron stick on my...
Forum: JR Radio & Spektrum Radios
12-30-2002, 03:46 PM
Replies: 5
Views: 655
Posted By ARP35

R700 got wet???

Thanks Danny, I will send them in.
Forum: JR Radio & Spektrum Radios
12-30-2002, 02:58 AM
Replies: 5
Views: 655
Posted By ARP35

R700 got wet???

I tried a different crystal and no luck. I also have one 537 servo that will not respond to a transmitter signal but it does power/center up. I have tried to get the receiver to respond but no...
Forum: JR Radio & Spektrum Radios
12-29-2002, 06:17 AM
Replies: 5
Views: 655
Posted By ARP35

R700 got wet???

Hi,
I crashed and the airplane landed upside down on a lake shore. The receiver R700 got wet but not soaked. I opened it up and sprayed it with electrical contact cleaner. When I hook up the...
Forum: Beginners
12-20-2002, 09:19 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Great news...the tank held up fine and so did the plane. However the pilot was a nervous wreck! Fortunately I solo'd and cut the umbilical cord from my instructor. I will say it was without small...
Forum: Beginners
12-20-2002, 01:51 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Thanks for the repair info... I pulled the tank out and it did have two 1/16" holes in the front bottom third. The replacement tank was a little different shape so I used a small exacto saw to get...
Forum: Beginners
12-19-2002, 08:28 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Ok...my SOF said it may hold for a flight or two but like all of you said it won't last. I bought a 320cc fuel tank and will replace it tonight. Hopefully I won't bust something else while fixing...
Forum: Beginners
12-19-2002, 03:35 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Ok...I am going to take the plane to my trainer who also owns the local hobby shop and ask his opinion. I just didn't want too because I'll have to do the walk of shame into the store. But I do...
Forum: Beginners
12-18-2002, 10:11 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Thanks for all the replies. When I installed the tank I coated the top that fits up against the firewall with silicone rtv. I think when I reinstalled the nose gear bracket, the screw went through...
Forum: Beginners
12-18-2002, 02:27 PM
Replies: 27
Views: 3,453
Posted By ARP35

Help...drilled hole into fuel tank

Hi all,
I had my first solo flight and landed alittle nose first. Anyway, the nose gear ripped off the firewall. I was replacing the nose gear bracket and pre-drilling the screw holes (the old...
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.