RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Flying Bougie
Showing results 1 to 16 of 16
Search took 0.32 seconds.
Forum: HPI Monster Truck Forum
07-03-2018, 03:02 PM
Replies: 10
Views: 2,746
Posted By Flying Bougie

What exactly part no / how many cc is that tank,...

What exactly part no / how many cc is that tank, and is that rick -> lean issue gone for good for you ?
Forum: RC Car Engines
06-09-2018, 06:27 AM
Replies: 3
Views: 2,954
Posted By Flying Bougie

This post goes back a bit but I have a similar...

This post goes back a bit but I have a similar dilemma. Putting a LRP ZR.30 into a savage, however I am looking for a back plate & pullstart for the ZR.30 which is a start box buggy set-up. I heard...
Forum: RC Monster Trucks
01-31-2011, 01:10 AM
Replies: 3
Views: 557
Posted By Flying Bougie

RE: More start-up issues

Went back to stock on HS (haven't touched LS yet). Stock is 2.5 turns out, curtousy of an old thread.

Pulled the air filter so I could a little more what was going on. Then got it running today...
Forum: Beginners
01-30-2011, 07:26 PM
Replies: 15
Views: 1,239
Posted By Flying Bougie

RE: Start-up issues ...

Well the engine runs great at top end, a slight bit richer than max rpm,very smooth and throwing a thin puff of white smoke. HS valve opened 1.5 turns. Looks as though i'm quite close with the LS...
Forum: Beginners
01-30-2011, 05:20 AM
Replies: 15
Views: 1,239
Posted By Flying Bougie

RE: Start-up issues ...

Well after cleaning thoroughly the carb, and changing to new fuel (just in case) my problem is solved. Now it seems to run well on the HS needle adjustment so I need to tune it a bit tomorrow. It...
Forum: Beginners
01-29-2011, 07:17 PM
Replies: 15
Views: 1,239
Posted By Flying Bougie

RE: Start-up issues ...

Some updates :

- glow plug is good, changed it anyway for good measure.
- adjusted (again) HS valve back to factory settings, about 2 1/4 - 2 1/2 turns out.
- found LS valve adjustment...
Forum: RC Monster Trucks
01-23-2011, 06:35 PM
Replies: 3
Views: 557
Posted By Flying Bougie

More start-up issues

Hi All,

I just bought a HSP nitro 1/8 scale monster truck a 21 size nitro. I want to do a break in so I was going about it the other weekend.

I didn't adjust the needles, I just primed it...
Forum: Beginners
01-23-2011, 06:20 PM
Replies: 15
Views: 1,239
Posted By Flying Bougie

RE: Start-up issues ...

Hi FLAPHappy, yes I did ask for advise. And no offence intended, but no need to send me off blowing bubbles. I'd rather check the basics first and I think it is basic info that the low end should be...
Forum: Beginners
01-23-2011, 03:19 PM
Replies: 15
Views: 1,239
Posted By Flying Bougie

RE: Start-up issues ...

Thanks for the inputs.

- I think the plug is good, but I will check the color and condition, as well as the "glow", I have another so if in doubt i'll probably replace it although I don't think...
Forum: Beginners
01-23-2011, 05:48 AM
Replies: 15
Views: 1,239
Posted By Flying Bougie

Start-up issues ...

Hi All,

I have had a case where I think I was trying to run an engine too lean previously. It was running ok, idling fine and throttling up to about 1/3 but then would die. I would try to adjust...
Forum: Beginners
06-08-2010, 08:27 AM
Replies: 49
Views: 10,535
Posted By Flying Bougie

RE: Powermaster fuel?? No more?

^ that sounds like nice and clean moonshine .. :-)
Forum: Beginners
06-07-2010, 06:23 AM
Replies: 7
Views: 1,324
Posted By Flying Bougie

RE: Break-in for 25 Glow Engine ...

Appreciating all the above infos and suggestions. Thanks ..

Based on all above, my low speed needle valve should be hidden behind a blackened 8mm needle plug (not to far from the fuel nipple)....
Forum: Beginners
06-06-2010, 06:20 AM
Replies: 7
Views: 1,324
Posted By Flying Bougie

RE: Break-in for 25 Glow Engine ...

I've only adjusted the main needle valve one way or the other so far at about 30-40 % full throttle, to make it run smoothly .. I guess only slightly rich. And from idle to 30-40% range, it runs...
Forum: Beginners
06-06-2010, 03:56 AM
Replies: 7
Views: 1,324
Posted By Flying Bougie

Break-in for 25 Glow Engine ...

Hi All,

Firsly I was going to break in an OS46, that was in a bi-plane. But since I am a beginner (long time fan and hobbiest .. but with low flying experience) , i decided to get a 25 size...
Forum: Beginners
03-17-2008, 07:45 AM
Replies: 20
Views: 3,404
Posted By Flying Bougie

RE: Beginner build of an Anniversary Edition Piper Cub

So which is the best clipped wing cub ARF and build kit 40-46 size that is a decent scale model ? And what about the J3 Cub 52 (blue) ? I just LOVE those plans .... I have a os 46 ax that could...
Forum: Beginners
03-14-2008, 06:47 AM
Replies: 30
Views: 2,846
Posted By Flying Bougie

RE: Nitro trainers...

To a tree, balsa wood and MonoKote taste just like chicken!

:D:D:D



So many people talk about the avistar. I have an ultimate bipe (on the shelf) and am also wondering about an ARF...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.