RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: owinfrey
Showing results 1 to 17 of 17
Search took 0.33 seconds.
Forum: Glow to Electric Conversions
12-10-2010, 05:12 PM
Replies: 6
Views: 6,034
Posted By owinfrey

RE: 45

Man... the Slicks are really nice. Once I get this one up in the air to train on, I'll get a Slick. Thanks for the link.
Forum: Glow to Electric Conversions
12-10-2010, 03:52 AM
Replies: 6
Views: 6,034
Posted By owinfrey

RE: 45

Hi Tofast... I just bought the same plane and was wondering what electronics you decided on and how was the maiden flight? I
Mine was missing a few parts like wheel pants, brushless motor mount and...
Forum: Tips & Techniques
09-14-2010, 10:47 PM
Replies: 29
Views: 23,405
Posted By owinfrey

RE: Plane Stand with CG balancing tool

Hi Guys, I was inspired by Attigs design and wanted to use lighter material I had around the house. I used the same idea but with pvc. The rack is sturdy enough to support two or three planes and the...
Forum: Tips & Techniques
08-22-2010, 03:25 PM
Replies: 29
Views: 23,405
Posted By owinfrey

RE: Plane Stand with CG balancing tool

I would also like a copy too. Thanks
[email protected]
Forum: T-Rex heli
03-19-2010, 08:42 PM
Replies: 5
Views: 1,005
Posted By owinfrey

RE: 450 Main and Tail Drive Gears

I've replaced the Main and Tail drive gear along with the one-way bearing and shaft. Also discovered the Main shaft was bent (grrrrrrrrrrrrrr), replaced it also.

Much thanks to everyone...
Forum: T-Rex heli
03-19-2010, 10:53 AM
Replies: 5
Views: 1,005
Posted By owinfrey

RE: 450 Main and Tail Drive Gears

Thanks for the reply, the belt is twisted in the right direction but how do I know is the one-way is in the right direction. Looking at the bottom of it, there is an arrow pointing counter clockwise....
Forum: T-Rex heli
03-18-2010, 10:09 PM
Replies: 5
Views: 1,005
Posted By owinfrey

450 Main and Tail Drive Gears

Hi Guys, I have a Trex 450 SA, bought used. I finally got a new motor/esc and programmed it. I'm facing problem with the drive gears. The main drive gear turns independently of the tail drive gear....
Forum: RC Helicopter Beginners Forum
12-08-2009, 05:13 PM
Replies: 3,893
Views: 333,789
Posted By owinfrey

RE: The Exceed Raptor G2 Upgraded

Hi Everyone,

It's been a long time since my last post. I finally wiped the dust off the G2 and upgraded it to a brushless motor and ESC. I got the Alpha 400 and Volcano 30A. After installing and...
Forum: Exceed RC Support - Helicopter
01-01-2009, 12:28 PM
Replies: 3
Views: 1,285
Posted By owinfrey

RE: G2 - Tail spinning counterclockwise

Yes... the exact same thing happens with me. I only replaced the tail gear from the set "50H08-26 Gear Set" because replacing it passed the gear test as mentioned in the orig post. I'm wondering if I...
Forum: Exceed RC Support - Helicopter
12-31-2008, 01:37 PM
Replies: 3
Views: 1,285
Posted By owinfrey

G2 - Tail spinning counterclockwise

Hi All,

I have a bushed G2 raptor and it started tail spinning counterclockwise.

I did the gear test by holding the tail rotor and turning the main rotor.

There was slippage, so I...
Forum: Exceed RC Support - Helicopter
12-15-2008, 04:46 PM
Replies: 8
Views: 1,337
Posted By owinfrey

RE: Need help with tail rotor

Hi Andy, the gyro comes on with the initialization and then goes off after about 6 second. At this point you can hear the twitching of the servo.
Forum: Exceed RC Support - Helicopter
12-11-2008, 08:51 PM
Replies: 8
Views: 1,337
Posted By owinfrey

RE: Need help with tail rotor

It seems that my problem is the gyro and not the servo. I disconnected the cables from the gyro and rx (right ctrl stick), swapped servos and the problem was now with swash plate control. The tail...
Forum: Exceed RC Support - Helicopter
12-09-2008, 10:22 AM
Replies: 8
Views: 1,337
Posted By owinfrey

RE: Need help with tail rotor

Thanks for replying Andy. No heat on the servo. I experience the glitchy noise and tail movement all the time except when the TX is off. This is a new heli, is this issue common? I'll need to get a...
Forum: Exceed RC Support - Helicopter
12-07-2008, 03:32 PM
Replies: 8
Views: 1,337
Posted By owinfrey

Need help with tail rotor

I'm new to the raptor g2 but have flown fixed pitch for training in the past. I got my g2 last week and have been reading several post about the tail rotor/rudder servo, etc..
I was able to over...
Forum: RC Helicopter Beginners Forum
12-06-2008, 09:36 AM
Replies: 3,893
Views: 333,789
Posted By owinfrey

RE: The Exceed Raptor G2 Upgraded

Thanks for the advice helifan... where should I order in the future?
Forum: RC Helicopter Beginners Forum
12-06-2008, 09:06 AM
Replies: 3,893
Views: 333,789
Posted By owinfrey

RE: The Exceed Raptor G2 Upgraded

Thanks drobin for replying.

xheli will send out replacement parts for each mentioned.
Forum: RC Helicopter Beginners Forum
12-05-2008, 02:57 PM
Replies: 3,893
Views: 333,789
Posted By owinfrey

RE: The Exceed Raptor G2 Upgraded

Hi Guys,

I just upgraded from the Falcon 40 and received my new exceed-g2 today. I was very excited, but upon inspection, I found the following:

1). The right stick trim moves to freely....
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.