RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 5
1
2
3
Last »
Search: Posts Made By: Tedstrickland
Showing results 1 to 25 of 102
Search took 0.34 seconds.
Forum: Walkera Helis - Dragonfly, etc..
02-17-2011, 12:08 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

The OEM charger will work fine....just take a bit longer to charge as you have a battery with increased capacity.

Make sure you have at least a 18-25C rating for the battery, as the 4G1B is a...
Forum: Walkera Helis - Dragonfly, etc..
07-29-2010, 07:20 AM
Replies: 2
Views: 824
Posted By Tedstrickland

RE: 5g6-1 take off problems

Always bind heli with throttle trim set to zero. If that doesn't work...swap motors to see if problem is a motor OR 4in1. Make sure to get gear mesh PERFECT !!!

Report back...we are here to...
Forum: Walkera Helis - Dragonfly, etc..
04-17-2010, 03:25 PM
Replies: 440
Views: 76,709
Posted By Tedstrickland

RE: Walkera 5#10

The conectors become critical as the curent starts to flow. Think of it as a "kink" in the garden hose of current flow. JST's do not transmit current well, and at 3.7 V (1S lipo), you are using...
Forum: Walkera Helis - Dragonfly, etc..
04-17-2010, 06:08 AM
Replies: 440
Views: 76,709
Posted By Tedstrickland

RE: Walkera 5#10

Sicheli,

I bought several 3.7V 1500 mAH lipo from Jason at Max Amps. They worked OK, but the problem is that the 5#10 is almost at it's max power with OEM weight, using the stock short-can...
Forum: Walkera Helis - Dragonfly, etc..
03-03-2010, 10:51 AM
Replies: 9,493
Views: 854,471
Posted By Tedstrickland

RE: Walkera #4 Fixed Pitch Helicopter Forum

The brass bushings loosening is a known issue. I have seen others use a bent peice of spring-steel to hold them in place (think stethascope -like going into both ears). Altrnatively, if you are...
Forum: Walkera Helis - Dragonfly, etc..
01-28-2010, 04:16 PM
Replies: 3
Views: 1,310
Posted By Tedstrickland

RE: ClubHeli - Awesome customer support!

Ditto that. Rick has outstanding service and fast shipping. I'll be back.....

Ted[sm=teeth_smile.gif]
Forum: Walkera Helis - Dragonfly, etc..
01-22-2010, 04:54 PM
Replies: 2
Views: 483
Posted By Tedstrickland

RE: 53Q3

The Walkera 53 series has good blade spacing, better than the stock CX birds, and better then any other 370-motor series co-ax, including the newer "Big Lama". Blade strikes are rare, as long as you...
Forum: Walkera Helis - Dragonfly, etc..
01-05-2010, 02:27 PM
Replies: 32
Views: 42,322
Posted By Tedstrickland

RE: Walkera WK-2801 8ch Multifunctional Transmitter Review

The instructions in the manual are a bit off. Go to the function you want to set to a Hot Key and enter into that function, simultaneously hold down the UP & DN keys and it will bring up Hot Key...
Forum: Walkera Helis - Dragonfly, etc..
01-05-2010, 01:10 PM
Replies: 32
Views: 42,322
Posted By Tedstrickland

RE: Walkera WK-2801 8ch Multifunctional Transmitter Review

On the WK2801E, I found that if you set-up the Hot Keys for funtions only available in 2801 mode, then go to 2401 compatible mode the Hot Keys still access to 2801-only functions, without having to...
Forum: Walkera Helis - Dragonfly, etc..
10-29-2009, 08:05 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

Leading edge of the paddles pointing slightly up !!!
Forum: Walkera Helis - Dragonfly, etc..
08-11-2009, 07:23 PM
Replies: 7
Views: 1,072
Posted By Tedstrickland

RE: 4#3b toiletbowl syndrome

Agree you need to check the flybar, and everything else on the head. But....How many flights do you have on the motor? It may be time for a new main motor..... Ted
Forum: Electric RC Helis
08-11-2009, 01:40 PM
Replies: 2
Views: 720
Posted By Tedstrickland

RE: DX6i where to buy

Did you ever find your DX6i and receiver? I have like new DX6i, w/ manual, nicads and a AR6100E receiver that you can have for a very reasonable price.

LMK, Ted
Forum: Walkera Helis - Dragonfly, etc..
08-11-2009, 12:14 PM
Replies: 440
Views: 76,709
Posted By Tedstrickland

RE: Walkera 5#10

Does anyone have a homepage for Turbo Ace. I did a bit of hunting and came up with this, http://turboace2000.1freecart.com/
but it looks like part of WOW hobbies. I would like to find a...
Forum: Walkera Helis - Dragonfly, etc..
08-11-2009, 11:29 AM
Replies: 2
Views: 597
Posted By Tedstrickland

RE: Switching 2601 TX from mode 2 to mode 1?

I think there is a dip switch on the inside of the transmitter. Go to the Walkera Home Page and Download any Heli manual that uses the 2601, and it will have complete instructions for conveting from...
Forum: Walkera Helis - Dragonfly, etc..
08-11-2009, 06:26 AM
Replies: 5
Views: 1,046
Posted By Tedstrickland

RE: tx-2401

Neither RX will work. The 4 CH WK 2401 will not allow you to set-up the swash-plate or other parameters for this type of heli. Not sure the 2401 will even work with a RX2801 or RX2701, even with...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 10:49 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

Eric,

When you get the set, you will notice that the flybar lock is also improved, so that it attaches on both sides of the guide ring.

P.S. Did you try using a magnet to see if you could...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 10:35 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

Look at the "guide ring set" HM-4G1B-Z-02. It includes this pin. It is pointed on the end.......to guide it in.....

Alternatively, on a real heli this would be called the "Jesus Bolt" as this...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 09:44 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

The rotorhead is attached to the upper part of the mainshaft. It has the spindle shaft with two "O" rings and two "C" clips. These act like a damper to allow blade "flapping". The blade grips...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 09:18 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

Are you talking about the spindle shaft, or the pin that holds the gear on the main shaft? The latter is a small tapered pin, not easily duplicated, but you could use short section of spring steel. ...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 04:57 AM
Replies: 2
Views: 726
Posted By Tedstrickland

RE: Help with Walkera 53Q3

Check that you have proper mesh in the gear-pinion, by manually running a small strip of paper thru the gears. The resulting corrugations should be similar. If one of the "meshes" is too close...
Forum: Walkera Helis - Dragonfly, etc..
08-09-2009, 04:48 AM
Replies: 2
Views: 555
Posted By Tedstrickland

RE: Recomendations for Tools for 4#3b

Don't need much.... Make sure you get a few high quality micro screwdrivers. I use the Wiha Screwdrivers: Specifically: the Phillips 000 and Phillips 00 sizes.

I've also fabricated a few...
Forum: Walkera Helis - Dragonfly, etc..
08-08-2009, 05:05 PM
Replies: 440
Views: 76,709
Posted By Tedstrickland

RE: Walkera 5#10

Ryan,

Just sent you a post at the other site. I would like to take the 2S off your hands. (I was just going to order the parts to build one myself). Please E-mail me at [email protected]....
Forum: Walkera Helis - Dragonfly, etc..
07-30-2009, 06:37 PM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

I ordered one of the New #4 motors, which is a standard 370SD, but with 2 large caps (noise filters) on the board it. The #4 appears to use the same servos as the 4G1B. I assume at 3.7V the ESC...
Forum: Walkera Helis - Dragonfly, etc..
07-30-2009, 04:44 AM
Replies: 52
Views: 11,299
Posted By Tedstrickland

RE: OFFICIAL Walkera 4G1B Thread

Just got the new Walkera Rx 2421, the 7.4V 4-in-1 for the upgraded #4, from ClubHeli. I will install soon and report back to ya' all. The new #4 appears to use the 4G1B head (except the new flybar...
Forum: Walkera Helis - Dragonfly, etc..
06-30-2009, 08:30 AM
Replies: 7
Views: 2,641
Posted By Tedstrickland

RE: Walkera Lama 400D question

Tail rotor is only decorative, and usually spins freely in the current created by the co-ax blades. All torque correction is done by the co-ax blades, so no tail-rotor required. TJS
Showing results 1 to 25 of 102
 
Page 1 of 5
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.