RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Extraviking
Showing results 1 to 19 of 19
Search took 0.31 seconds.
Forum: KingTech Turbines International
04-25-2015, 04:37 PM
Replies: 36
Views: 8,058
Posted By Extraviking

I thought this thread was about bad KingTech...

I thought this thread was about bad KingTech pumps, which I suspect my pump is, but if u are not interested in answering me properly here, i can create a new thread. The problem is that the engine...
Forum: KingTech Turbines International
04-25-2015, 10:53 AM
Replies: 36
Views: 8,058
Posted By Extraviking

My pump is ZP30020SF on my 180g but I have...

My pump is ZP30020SF on my 180g but I have flameout by fast downtrottle.
Pump Voltage is 65 at idle, is this abnormally high? Deacelration is 003.
Could it be the pump that cause flameout?
I must...
Forum: RC Jets
02-02-2015, 07:19 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

Tested today the gear, there was a big leak in...

Tested today the gear, there was a big leak in Mbar, now I've got enough trouble.
I want to mount a conventional gear failsafe .Tanks for yours help.
Perhaps it will be more questions from me,

...
Forum: RC Jets
02-01-2015, 10:48 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

What happens is exactly what you say,still...

What happens is exactly what you say,still appears and shows X in Device Explorer after a bit.
My plan was to use Ext1 and Ext 2 on the Mbar for the Mspeed and Xicoy GSU
I do not trust the system...
Forum: RC Jets
02-01-2015, 08:50 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

Thanks for your reply Wayne. The problem is...

Thanks for your reply Wayne.
The problem is that i need ext 2 for a servo.
Is it not possible with telemetry input in a CB200 if one needs 15 servo channels
Jetisystem sure OK, but setup Sensors...
Forum: RC Jets
02-01-2015, 08:00 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

Thanks for your reply. I have the latest...

Thanks for your reply.
I have the latest firmware 3.0.2 TX
The Ext port on the CB200 is set on Ex bus
Mbar appears on the Device Explorer but becomes disabled after about 20 sec
I am unsure which...
Forum: RC Jets
02-01-2015, 06:52 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

MBar problems. Wondering if there is someone...

MBar problems.
Wondering if there is someone who can tell me why I lose the signal from Mbar about 30 sec after I've turned on radio.If I disconect the signal wire from the mbar and connect it again...
Forum: RC Jets
01-27-2015, 10:49 AM
Replies: 67
Views: 7,668
Posted By Extraviking

My AW...

My AW 14,5http://www.rcuniverse.com/forum/attachment.php?attachmentid=2068287
Forum: RC Jets
01-19-2015, 05:08 PM
Replies: 67
Views: 7,668
Posted By Extraviking

Hi! Sounds great. Send it as a gift and set...

Hi!
Sounds great.
Send it as a gift and set the value at $ 20 for avoiding tax on it.
Thanks for the service.
Ola B
Forum: RC Jets
01-17-2015, 02:36 PM
Replies: 3,501
Views: 598,820
Posted By Extraviking

Thanks for the answer, i try this on a good day.

Thanks for the answer, i try this on a good day.
Forum: RC Jets
01-17-2015, 09:59 AM
Replies: 3,501
Views: 598,820
Posted By Extraviking

Should wanted to had a decent instruction on how...

Should wanted to had a decent instruction on how to get the brake on the elevator from middle and front (-100- + 100) which is activated when the gear is down. And how swing nose wheel only when when...
Forum: RC Jets
01-16-2015, 12:14 PM
Replies: 67
Views: 7,668
Posted By Extraviking

I also want to had a one for my 14.5 Airworld...

I also want to had a one for my 14.5 Airworld Hawk, is something missing without :)
Forum: RC Jets
08-04-2014, 12:11 PM
Replies: 3
Views: 620
Posted By Extraviking

Sorry this thread should be in Merlin...

Sorry this thread should be in Merlin turbine-clinic, but it is a kerostart that does not go to preheat but shows ignition failure

Ola B
Forum: RC Jets
08-04-2014, 08:24 AM
Replies: 3
Views: 620
Posted By Extraviking

160 mk3

Hello!
Having trouble with the ignition on my Merlin 160 mk 3.
Fuel supply is ok, battery is ok.Har tried to adjust the starting volt pump up and down, now stands at 18, some guys involved in...
Forum: KingTech Turbines International
05-06-2014, 03:52 PM
Replies: 52
Views: 12,139
Posted By Extraviking

I recently bought a King Tech G180, no problem,...

I recently bought a King Tech G180, no problem, but could not buy their oil.Is there any way I can get hold of Kingtech oil here in Scandinavia / Europe?

Ola B
Forum: RC Jets
12-06-2013, 10:39 AM
Replies: 15
Views: 2,708
Posted By Extraviking

Great that it worked out, then I have nothing to...

Great that it worked out, then I have nothing to fear :-)
Forum: RC Jets
12-06-2013, 05:55 AM
Replies: 15
Views: 2,708
Posted By Extraviking

Dreamworks should have tested this combination...

Dreamworks should have tested this combination before they put it up for sale.
If it does not work with Jet Tronic valve, it becomes a very expensive pressure gauge.
Forum: RC Jets
12-06-2013, 03:30 AM
Replies: 15
Views: 2,708
Posted By Extraviking

I have the same Jet tronic and GSF 150 but have...

I have the same Jet tronic and GSF 150 but have not assembled and tested yet.
Did you get it to work together by following the steps Todd said?
Forum: RC Jets
10-13-2013, 09:34 AM
Replies: 714
Views: 229,090
Posted By Extraviking

Does anyone have picture of Smoke Tank...

Does anyone have picture of Smoke Tank installation?, I have a Rookie tank but can not find some clever way to install it.
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.