RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mcfly1950
Showing results 1 to 18 of 18
Search took 0.62 seconds.
Forum: Questions and Answers
06-07-2004, 07:25 PM
Replies: 7
Views: 1,765
Posted By mcfly1950

Exhaust extension for Saito

I have a Saito 80. Due to the mounting constraints, I need a muffler extension. Two of the readily available rubber types have failed from burn through. Another fell off in flight. Does anyone know...
Forum: ARF or RTF
03-28-2004, 03:03 PM
Replies: 6
Views: 707
Posted By mcfly1950

RE: Hanger 9 Cessna

Watch out for the landing gear as well. Its soft stuff, bends easily. I've been flying RC since 1971, I have a Sweet Stick with over 1009 flights so I don't think that this is a pilot issue. Thanks,...
Forum: ARF or RTF
03-27-2004, 07:29 AM
Replies: 6
Views: 707
Posted By mcfly1950

RE: Hanger 9 Cessna

Its the horizontal stab. Its a built up stab, has some flex to it. I just don't see anything abnormal.
I was going to add flying wires. Keep in mind that this is an ARF
Forum: ARF or RTF
03-26-2004, 09:08 PM
Replies: 6
Views: 707
Posted By mcfly1950

RE: Hanger 9 Cessna

Thanks for the suggestion. The problem seems more like an issue with the stab as thats where the flutter is. The elevator seem ok. Hinges tight.
Forum: ARF or RTF
03-24-2004, 10:16 PM
Replies: 6
Views: 707
Posted By mcfly1950

Hanger 9 Cessna

I have a Hanger 9 Cessna Skylane 182. Its a 6.5 lb plane powered with a Saito 65. Today while flying at half throttle I noticed that the horizontal stab was fluttering. (Keep in mind that this plane...
Forum: Glow Engines
02-21-2004, 01:31 PM
Replies: 2
Views: 478
Posted By mcfly1950

RE: Saito 65 and 72

Jim,
Thanks for the info.... I guess I'll consider an 80
Forum: Glow Engines
02-21-2004, 08:35 AM
Replies: 2
Views: 478
Posted By mcfly1950

Saito 65 and 72

I currently have a Hangar 9 Cessna 182. I have a Saito 65 turning a 12x8 I am considering a Saito 72 for more power. I'd like to be able to swap engines with out repositioning the mounts. Is there a...
Forum: Glow Engines
12-06-2003, 09:34 PM
Replies: 1
Views: 434
Posted By mcfly1950

RE: Laying up a Glow engine for 6 months

Before I lay up an engine, run it. Get it to operating temp. While its running at half throttle I pull the fuel line. Once it quits, I try to restart it without the fuel line connected. Most times...
Forum: Glow Engines
11-23-2003, 06:39 PM
Replies: 2
Views: 457
Posted By mcfly1950

RE: OS Max 40RC H

Thanks.... I'll try this approach....

Mike
Forum: Glow Engines
11-23-2003, 05:23 PM
Replies: 2
Views: 457
Posted By mcfly1950

OS Max 40RC H

Can anyone tell me where to find a piston, ring and liner for and old 40 RC H? Are there any other OS parts that would work if original nparts are unavailable?
Forum: Glow Engines
11-21-2003, 02:54 PM
Replies: 2
Views: 547
Posted By mcfly1950

RE: OS Max H 40

Can you tell me where to find a piston, ring and liner for and old 40 RC H?
Forum: O.S. Engines Support
11-20-2003, 03:36 PM
Replies: 1
Views: 429
Posted By mcfly1950

OS Max H

Does anyone know where I can get part for an old 40H RC I need ring and a liner.
Forum: O.S. Engines Support
08-19-2003, 01:06 AM
Replies: 3
Views: 627
Posted By mcfly1950

OS carb # 7DV

Can you tell me what glow plug this engine requires? Thanks for your help / reply....
Forum: Glow Engines
08-17-2003, 08:43 PM
Replies: 2
Views: 1,008
Posted By mcfly1950

OS 7DV carb

Chuck,
Thanks for the reply. I know of the + & - that you refer too. I'll try that......

Mike
Forum: Glow Engines
08-15-2003, 07:48 PM
Replies: 2
Views: 1,008
Posted By mcfly1950

OS 7DV carb

I have a great OS 61 that ha a clean top end but runs too rich at idle.
Can some one tell me how to set the low / idle mixture on this carb.
Forum: O.S. Engines Support
08-14-2003, 07:03 PM
Replies: 3
Views: 627
Posted By mcfly1950

OS carb # 7DV

I have a new OS .61 (circa 1982) engine with a 7DV carb. I need instructions as to how to go about setting the low speed adjustment.
I can get a clean top end but the low end it too rich. How /...
Forum: O.S. Engines Support
05-14-2003, 12:40 AM
Replies: 3
Views: 947
Posted By mcfly1950

OS Max 40 RC

Are throttle arms from newer OS engines interchangeable with an old 1979 OS Max 40?
Forum: O.S. Engines Support
05-13-2003, 12:55 AM
Replies: 3
Views: 947
Posted By mcfly1950

OS Max 40 RC

I have an older 1979 OS Max 40 RC. I need a throttle arm, piston and ring....
Any leads as to where I can find parts?
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.