RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Muciek
Showing results 1 to 10 of 10
Search took 0.13 seconds.
Forum: Engine Conversions
12-18-2012, 02:08 PM
Replies: 1,123
Views: 240,243
Posted By Muciek

RE: CDI gr8flyer55

It's Netframework


EDit: sorry I was late with this answer. Didnt see other one's<br type="_moz" />
Forum: Engine Conversions
11-11-2012, 02:44 PM
Replies: 1,123
Views: 240,243
Posted By Muciek

RE: CDI gr8flyer55

How can I compile a picf1840 version into hex?
Forum: Engine Conversions
11-02-2012, 01:14 PM
Replies: 1,123
Views: 240,243
Posted By Muciek

RE: CDI gr8flyer55

It's only painted to show how it works in 4t the degree of advance are different on each engine but it should look like this (raising with rpm)
Forum: Engine Conversions
11-02-2012, 10:26 AM
Replies: 1,123
Views: 240,243
Posted By Muciek

RE: CDI gr8flyer55

This looks like 2t curve... http://i.imgur.com/C2JkB.jpg   here is one for a 2t.    A 4 stroke ignition should have curve like this low rpm few degrees higher rpm more deegrees here is a...
Forum: Engine Conversions
08-03-2012, 11:36 PM
Replies: 1,123
Views: 240,243
Posted By Muciek

RE: CDI gr8flyer55

Key to this is good DC converter http://www.youtube.com/watch?v=zNcA0oYLj1s http://www.youtube.com/watch?v=OhG4M2WEM9w
here are my projects. This one used in motorcycle can start from 7v generating...
Forum: Engine Conversions
08-27-2011, 02:49 AM
Replies: 557
Views: 144,120
Posted By Muciek

RE: Complete new CDI - website open

Ah ok. Thx :D
Forum: Engine Conversions
08-26-2011, 01:07 PM
Replies: 557
Views: 144,120
Posted By Muciek

RE: Complete new CDI - website open

Ok, One more question. Do I have to put pick up coil before the angle that I want to put in table ? For example coil is set at 25*BTDC in map I set 39* advance will it work or I have to put it before...
Forum: Engine Conversions
08-26-2011, 10:21 AM
Replies: 557
Views: 144,120
Posted By Muciek

RE: Complete new CDI - website open

Ok, I have programmed it. I was experiencing a problem with RS232 to TTL module after switching rx and tx it started working.I want to ask will it work with coil sensor instead of Hall unit? <span...
Forum: Engine Conversions
08-03-2011, 01:43 PM
Replies: 557
Views: 144,120
Posted By Muciek

RE: Complete new CDI - website open

So I can't use this usb to ttl module like this man right herehttp://www.swharden.com/blog/2009-05-14-simple-case-avrpc-serial-communication-via-max232/ To programm PIC ?
Forum: Engine Conversions
08-03-2011, 12:44 PM
Replies: 557
Views: 144,120
Posted By Muciek

RE: Complete new CDI - website open

Hi. I have build a timer board and usb to ttl module. But i'm experiencing problems Can I programm PIC (put hex file into memory) using this usb to ttl module or I need other programmer? Here you...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.