RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: jmflying
Showing results 1 to 11 of 11
Search took 0.63 seconds.
Forum: Engine Conversions
01-30-2005, 10:14 AM
Replies: 2
Views: 1,142
Posted By jmflying

RE: Reed valve issue on Ryobi 31cc

The reed bolts down in place with a limiter on top. I will try turning it over thanks for the info.
Forum: Engine Conversions
01-29-2005, 09:00 PM
Replies: 2
Views: 1,142
Posted By jmflying

Reed valve issue on Ryobi 31cc

Does any one know if the stock reed valve should sit flat on the carb spacer and be sealed or does it have a slight curve inward to produce nore retun spring pressure. I opened up my ryobi and the...
Forum: JR Radio & Spektrum Radios
04-20-2004, 10:15 AM
Replies: 3
Views: 828
Posted By jmflying

RE: Need help with New 8103DT w/DS811 servos flutter on the ground

Thank you for the reply Danny, also the flaps run by 2 JR 537's oscillate violently. I have 3 700 receivers, will they have the same feed back issue. There is zero lash in all control surfaces, the...
Forum: JR Radio & Spektrum Radios
04-19-2004, 10:34 AM
Replies: 3
Views: 828
Posted By jmflying

Need help with New 8103DT w/DS811 servos flutter on the ground

I installed a New Radio and set up in H9 Ultra Lite 120 stick, I am using a Jr549 recvr and DS811's on elev, rud,ailerons, I am using JR537's on flaps, throttle and smoke valve. I am running a...
Forum: Extreme Speed Prop Planes
02-13-2004, 06:33 PM
Replies: 30
Views: 5,040
Posted By jmflying

RE: Custom patriot and webra 120

I have an older Webra 120 about the best running engine I have had. With an APC 15x6 15% Power Master it turns 11,300 with a pitts style muffler same setup APC 16x6 turns 9600. I run it with the 15x6...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-06-2003, 05:08 PM
Replies: 29
Views: 16,429
Posted By jmflying

RE: Precedent Stampe

I had a Precedent Stampe from 1986 to 1991 traded it off, then bought it back, kep it till 1996 bought real plane sold all RC stuff. I bought another kit in 1999 paid $229.00 US dollars. I have a...
Forum: Glow Engines
10-30-2003, 02:35 PM
Replies: 57
Views: 6,580
Posted By jmflying

RE: Tower Hobbies engine problems

Thank you all for the input, thank you Bill B for responding. I would have been more happy with you sending me a new cyl and piston, but I guess I have no choice but to box up this engine and ship it...
Forum: Glow Engines
10-29-2003, 04:43 PM
Replies: 57
Views: 6,580
Posted By jmflying

RE: Tower Hobbies engine problems

I also need to add. I bought this TH 46 because I have 3 friends and they each have a TH 75 2 out of 3 run great. 1 is new and just went thru the break in procedure and only has 3 flights on it. 2...
Forum: Glow Engines
10-29-2003, 04:09 PM
Replies: 57
Views: 6,580
Posted By jmflying

RE: Tower Hobbies engine problems

To Bill Baxter, I need to add a little history I started flying RC in 1986 and flew daily until 1996 when I bought a real airplane. During that period I bought and broke in numerous glow engines even...
Forum: Glow Engines
10-28-2003, 02:47 PM
Replies: 57
Views: 6,580
Posted By jmflying

Tower Hobbies engine problems

I bought a Tower Hobbies .46abc did the complicated break in procedure exactly as printed in the instructions, I have run 2 gallons of PowerMaster 10% through engine. It will only tach 10700 to 10900...
Forum: Glow Engines
10-28-2003, 02:00 PM
Replies: 23
Views: 1,781
Posted By jmflying

RE: Tower .75 worth the $$$ ?

I bought a Tower Hobbies .46abc did the complicated break in procedure exactly as printed in the instructions, I have run 2 gallons of PowerMaster 10% through engine. It will only tach 10700 to 10900...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.