RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: pilotwon
Showing results 1 to 16 of 16
Search took 0.59 seconds.
Forum: Gas Engines
05-04-2021, 05:23 PM
Replies: 18
Views: 7,222
Posted By pilotwon

The original carb on the G-38 was a WT6. It was...

The original carb on the G-38 was a WT6. It was discontinued years ago and Zenoah replaced it with the WT338. I have two G-38's both equipped with the RCXCEL ignition conversion. They run great,...
Forum: Marketplace
09-04-2018, 03:00 PM
Replies: 5
Views: 796
Posted By pilotwon

Chipmunk Canopy

Discovered the Fiberglass Specialties still makes both the canopy and the engine cowl for the Goldberg Super Chipmunk. They are very reasonably priced.
Forum: Marketplace
08-08-2018, 08:38 PM
Replies: 5
Views: 796
Posted By pilotwon

Goldberg Chipmunk

I'm looking for a canopy for a Goldberg Chipmunk. Any chance you may have one or know where I might find one?
Forum: Beginners
10-09-2017, 08:43 PM
Replies: 13
Views: 5,274
Posted By pilotwon

pilotwon

I have used Nelson Paints a lot in the last few years. Does anybody know what happened to John Desilets and/or Nelson Hobbies. His website is no longer active. It would be a shame to not be able to...
Forum: RC Scale Aircraft
07-18-2007, 10:18 AM
Replies: 8
Views: 1,338
Posted By pilotwon

Flying Wire Material

Does anyone out there know of a source for scale flat flying wire 1/8" to 3/16" wide? Nelson Hobby no longer handles the material.
Forum: Gas Engines
07-14-2007, 10:44 PM
Replies: 13
Views: 3,823
Posted By pilotwon

RE: Zenoah GT-80 Twin

Thanks a lot. That really does help. And thanks for the reference to the Toni Clark website. Didn't know about it.
Forum: Gas Engines
07-14-2007, 12:16 AM
Replies: 13
Views: 3,823
Posted By pilotwon

RE: Zenoah GT-80 Twin

Thanks. I plan on putting the GT-80 on a 1/5 scale Grumman Duck and I am at the point of putting the firewall in place.
Forum: Gas Engines
07-13-2007, 07:51 PM
Replies: 13
Views: 3,823
Posted By pilotwon

RE: Zenoah GT-80 Twin

Thanks for the reply. Here is what I need:
1. Drive washer to back of mount
2. Overall width ( I assume the spark plugs are at the widest point)
3. Bottom of carb to top of engine
4. ...
Forum: Gas Engines
07-13-2007, 07:45 PM
Replies: 15
Views: 1,274
Posted By pilotwon

RE: My G-26 went south after 4 months

The idea that the carb is gummed up from sittong for a while is very possible. However, I have cleaned the carb from stem to stern and had no luck getting them to run correctly. I know every...
Forum: Gas Engines
07-12-2007, 07:39 PM
Replies: 13
Views: 3,823
Posted By pilotwon

Zenoah GT-80 Twin

Does anybody have a diagram showing all the dimensions for a Zenoah GT-80 twin? The diagram and chart in the Zenoah general manual you can download online is useless.
Forum: Gas Engines
07-12-2007, 07:37 PM
Replies: 21
Views: 1,849
Posted By pilotwon

RE: odd G-26 problem

Mine does the same thing installed on an Ultra Stick Lite. Usually it only happens on the first flight of the day but will do it almost any time I refuel. Never misses a beat after that. I just...
Forum: Gas Engines
07-12-2007, 07:29 PM
Replies: 10
Views: 1,342
Posted By pilotwon

RE: G 26 Zenoah Hand Start - How Hard?

My son and I each have an Ultra Stick Lite with a G-26 and it is a great combination. The G-26 is an easy starting engine and a good running engine. We had Ralph Cunningham at RC Igntions put CH...
Forum: Gas Engines
07-12-2007, 07:16 PM
Replies: 16
Views: 5,833
Posted By pilotwon

RE: HELP! zenoah G38 will not flip start but will start with starter or rope

Check your magnet to rotor gap. Usually when a G38 won't flip start that is the problem. The gap should be .002". If it is as much as .005" it will be harder to start. I have a G38 and when it...
Forum: Gas Engines
07-12-2007, 07:12 PM
Replies: 15
Views: 1,274
Posted By pilotwon

RE: My G-26 went south after 4 months

I have two G26 engines and they both run great. However I have made a couple of mods to both of them. First, Ralph Cunningham installed a CH ignition in both of them. Gained about 400 static RPM...
Forum: Questions and Answers
06-11-2007, 11:26 AM
Replies: 12
Views: 5,094
Posted By pilotwon

RE: What happened to Dave Patrick Models?

;)Electro-Dynamics has the color coded extensions in lengths from 3" to 48" in black, blue, green, yellow and red.
Forum: Seaplanes
03-05-2004, 08:58 PM
Replies: 14
Views: 8,166
Posted By pilotwon

RE: Grumman Duck

I am building a Duck and bought the plans from Louis Pancoast. Larry Katana at Precision Cut Kits cut the parts and did a beautiful job. Pancoast is in Courdalaine (sp?) Idaho and is in the HIgh...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.