RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: antomo
Showing results 1 to 12 of 12
Search took 0.61 seconds.
Forum: Park Flyers & Backyard Flyers
07-06-2004, 01:17 PM
Replies: 5
Views: 1,663
Posted By antomo

RE: swiss trainer

Hi Marty,

I'm happy to hear that you had a successfully flight, even with the small problems that you faced. (the important think is to have it in one piece).
I install a Himark 2015-3600 with...
Forum: Park Flyers & Backyard Flyers
06-25-2004, 06:50 AM
Replies: 5
Views: 1,663
Posted By antomo

RE: swiss trainer

Hi,

I almost finished but i'm still afraid to fly it.
So i have a depron 3DX and play with until i feel confident.
I request from bohemia the English instructions so i didn't find any...
Forum: Electric RC Jets
05-30-2004, 02:05 PM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

just over 30 flights with 3 cell Lipoly 1500 and one of the motor failed.
The problem was that the back brass "bearing" (i do not know the correct word) destroyed.
Possible if i had put a drop of...
Forum: Park Flyers & Backyard Flyers
05-02-2004, 02:36 PM
Replies: 5
Views: 1,663
Posted By antomo

swiss trainer

Hi,
Has anyone build the swiss trainer from bohemia models??
Any building tips and suggestions are more than welcome.
Forum: Electric RC Jets
04-20-2004, 01:16 PM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Hi,
Was calm, 2 to 3 mph.
I'll try again this weekend with CG 57 from 50 and better landing system.
Forum: Electric RC Jets
04-18-2004, 07:39 AM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Yes, finally it flies.
setup 1-2mm more movement at aileron and elevator (wrong was too sensitive)
with 80% throttle and a little trim up the plane still needs up to maintain attribute (i don't...
Forum: Electric RC Jets
04-17-2004, 08:26 AM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Ready to fly!!!:eek:
setup:
3s1p 1500 Kokam
edf55 150
ICS400!! (hope to handle the 2 more volts from the specs)[X(]
weight 578 grams
thrust 300 grams approximately

I'll perform a...
Forum: Electric RC Jets
04-14-2004, 05:50 PM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Hi,
With throttle management i hope to have lot of flights (if not crashed) with the stock motors.
In case of burned motor you have to find the small hole in the fan, open there a small hole for...
Forum: Electric RC Jets
04-13-2004, 12:18 PM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Hi all,
The second one within a month period.
after reading a lot i decided to go on with Lipoly 3cells 1500ma and EDF 55 150:D.
Not to use weight for correct CG and to save my batteries in a...
Forum: Electric RC Jets
04-02-2004, 02:51 PM
Replies: 3
Views: 851
Posted By antomo

A10 help

Hi,
a few questions for the GWS A10 with EDF55 150:
are the power/motor cables supplied with the kit capable to handle the requested current? (10-15 Amps)
Suggested batteries? (no KAN cells or...
Forum: Electric RC Jets
03-22-2004, 04:04 AM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

EDF 55 exists in two versions (150 and 300)
with the 150 (280 motor) i perform a test with 8 cells NiMh AAA 700ma.
It was no good!! Static test, and the pack was too hot after a minute.
Three 4...
Forum: Electric RC Jets
03-21-2004, 01:56 PM
Replies: 196
Views: 49,363
Posted By antomo

RE: GWs A10 EDf55's

Hi,
I'm Antonis from Greece.
A10 was my first ducted fan, and i say was because i crash it on a tall tree.
The plane was with the 55 fan's.
First try with 2 Lithium cells (crash in 5 meters)...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.