RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Ron Olson
Showing results 1 to 9 of 9
Search took 0.02 seconds.
Forum: Speed - RC Gas Boats
06-21-2020, 03:17 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

It's pretty simple. Use the corrugated cardboard...

It's pretty simple. Use the corrugated cardboard so that the flutes run the length of the hull then set the engine in there. That will set the engine at the angle you need and give you some gap to...
Forum: Speed - RC Gas Boats
06-19-2020, 07:41 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

Set the engine in the boat using a piece of...

Set the engine in the boat using a piece of double-walled cardboard. It will then naturally find its own angle..
Forum: Speed - RC Gas Boats
06-09-2020, 06:59 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

Try the center of the spark plug as that puts it...

Try the center of the spark plug as that puts it very close.
Forum: Speed - RC Gas Boats
06-09-2020, 05:52 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

I ran my 45" Assault mono last Saturday with a...

I ran my 45" Assault mono last Saturday with a 7016/3 prop on it, she scooted right across the water!
I mounted mine at 33% forward of the transom, just a hair under 15".
Forum: Speed - RC Gas Boats
06-09-2020, 03:40 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

Zippkits has a nice selection for the price as...

Zippkits has a nice selection for the price as most are already sharpened and balanced; the 470, 570, 670, 7016/3 and Prather 270 are some good choices.
Forum: Speed - RC Gas Boats
05-21-2014, 12:04 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

Tom hit it again. Bonzi' does have probably the...

Tom hit it again. Bonzi' does have probably the best prices around for stock Zenoah's as for a few dollars more you can have the real thing but unfortunately that's about the only thing that I'd buy...
Forum: Speed - RC Gas Boats
05-20-2014, 02:23 PM
Replies: 27
Views: 4,074
Posted By Ron Olson

Like I posted earlier, I have one but just...

Like I posted earlier, I have one but just haven't dropped it in a hull yet. I probably ought to at least pop the top off to see what's inside.
Forum: Speed - RC Gas Boats
05-20-2014, 11:04 AM
Replies: 27
Views: 4,074
Posted By Ron Olson

OK, Tom beat me to it! :) You may have lucked...

OK, Tom beat me to it! :)
You may have lucked out as if the boat already had theK&B in it then it should have a 1/4" drive installed so that'll save you a bunch right there.
I've used a lot of the...
Forum: Speed - RC Gas Boats
05-20-2014, 08:27 AM
Replies: 27
Views: 4,074
Posted By Ron Olson

Five inches is the norm with gas engines. Your...

Five inches is the norm with gas engines. Your boat should already have 5" rails in it.
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.