RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Hesco Racing
Showing results 1 to 11 of 11
Search took 0.08 seconds.
Forum: Speed - RC Nitro Boats
09-20-2007, 11:41 PM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Wave nice numbers but I am sure with a few minor changes you'l be far over 50mph.
1. Loose the teflon liner and 3/16 shaft. Although that teflon liner is slippery like snot when it warms up its...
Forum: Speed - RC Nitro Boats
09-15-2007, 01:05 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Why dont you just cup the 240 first before going to a 245. I think the bigger prop might hinder your stibbility.
Forum: Speed - RC Nitro Boats
09-04-2007, 12:44 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Thats weird I see you throttle servo is a futaba and they are good servos. I dont like putting servos on their side, The engineer in me says that the servo will work harder as all the gears lay in...
Forum: Speed - RC Nitro Boats
09-02-2007, 12:45 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

I could be wrong but I see a steel bolt in both mountings of your rudder. If so you wont get the nockout effect of the rudder. Replace bottom with brass screw. They sheer off nicely.
Forum: Speed - RC Nitro Boats
08-25-2007, 12:54 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

That tank is quite small. I run a 12 oz tank in my TC and only get 7 minutes of running isnt that OS is a bit more thursty ?
Forum: Speed - RC Nitro Boats
08-24-2007, 11:39 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Ok the best you can do now is snad it with 1000 water paper dry (not wet) it shoeld take the shine off it or use some scotch bride pad and make it dull.
Forum: Speed - RC Nitro Boats
08-24-2007, 09:43 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

NitroSS dont spray the bottom unless you know how to spray orange peel and please do not buff the bottom to be slick as snot thats the oppisit of what you want. When the bottom is to smooth it suck...
Forum: Speed - RC Nitro Boats
08-15-2007, 11:14 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

I dont know if its just hou the foto is taken but the motor looks high in the front. Maybe just the angle of the shadow playing tricks. Hell I turned that shaft off the first day I took out my TC....
Forum: Speed - RC Nitro Boats
08-14-2007, 12:33 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

I dont see any slotting of your mounts. How sure are you that it is in line with the cable tube. Are you going to run a larger diameter cable too handle the extra power. What are you going to do to...
Forum: Speed - RC Nitro Boats
07-11-2007, 09:33 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Amen to that piper chuck As mentioned before I changed my shaft to a 1/4" shaft and pack it with grease before every race day. One practice day had the boat run out due to radio problems and had...
Forum: Speed - RC Nitro Boats
07-11-2007, 09:12 AM
Replies: 116
Views: 14,125
Posted By Hesco Racing

RE: OS 46 powered TC31 the making...

Wave do you want to go faster or slower. Whats with the 2 water brakes at the bottom of your hull. Iff you want less drag make a water pickup like the picture below. we have been using it for years...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.