RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: flyrcjets
Showing results 1 to 18 of 18
Search took 0.10 seconds.
Forum: Extreme Speed Prop Planes
01-10-2004, 07:02 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: Question here/Torque Rods

Curious where you would move the main gear to balance the aircraft.
Forum: Extreme Speed Prop Planes
12-06-2003, 02:13 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: A little help PLEASE

Walt,
The fueler might be a good idea because there isnt alot of room to pull the line off to fuel!
Funny I ended up losing my canopies , so now I have two canopies one with a cockpit all...
Forum: Extreme Speed Prop Planes
12-05-2003, 02:58 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: A little help PLEASE

Forget the wood screws!..and no I have NO up or side thrust thrown in!.The inch I added was to the front of the cowling. But thats because the engine stuck out more then usual. Try putting your...
Forum: Extreme Speed Prop Planes
12-05-2003, 02:46 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: A little help PLEASE

Walt, Something is wrong here. It should mount A1 perfectly.If not somethings wrong.
I only had trouble getting my ENGINE to mount to the MOTOR MOUNT. BUT the mount should bolt in to the predrilled...
Forum: Extreme Speed Prop Planes
12-01-2003, 11:04 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

Hi Mark,
Yeah I have the .60 size but I'd think you can still do what I did. I used a smaller flat tank which rests above on braces of a bellcrank for the steering then the retract is forward in...
Forum: Extreme Speed Prop Planes
11-29-2003, 06:46 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

Sure I could believe that!
I think the point that needs to be made is that everything depends on how you build! If you have large gaps anywhere it causes problems.
But just like my Euro Firebird...
Forum: Extreme Speed Prop Planes
11-29-2003, 02:39 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

Crap hanging out of an aircraft is crap hanging out of an aircraft, slows you down..just like full scale!
Build however ya like but wheels do seal the wheel wells. Known fact for years and...
Forum: Extreme Speed Prop Planes
11-29-2003, 01:51 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

Then I guess full scale aircraft would be better with no retracts..since it sounds like wheel wells cause "turbulance'? Come on guys..if you have your wheels up they "seal" the well! There is NO...
Forum: Extreme Speed Prop Planes
11-29-2003, 12:15 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

I've flown mine both ways and With the retracts IT IS faster!
Forum: Extreme Speed Prop Planes
11-23-2003, 04:16 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

ummm I just mounted a jett .60 on the motor mount after I shaved it a bit and I have the remote needle valve which fits fine and it balances out great!..if you really have problems let m,e know and...
Forum: Extreme Speed Prop Planes
11-20-2003, 03:51 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

Did you use the torque rods that came with the plane??....... yeah they will work
Did you use the motor mount that came with it??..use it becasue it's about the only mount that will work!

...
Forum: Extreme Speed Prop Planes
11-19-2003, 10:09 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

hahaha...look at my scheme above and you'll see I went a bit crazy! But I did the base monocote first then glued in but you can do either way won't really matter! K
Forum: Extreme Speed Prop Planes
11-19-2003, 09:42 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

RE: DC F-20 Building Question

You put the rods in AFTER you install the stab..notch the corner and then glue the hinge/ rod holder in your cut out slot with epoxy after the stab is in! Hope that helps.... oh and yeah the rods...
Forum: Extreme Speed Prop Planes
08-09-2003, 11:02 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

sorry

Sorry I tried EVERY engine and have now settled on a Jett.60 in my F20... tuned pipe, his spinner..it's awesome..I can't imagined what you are saying about it being a "dud"
All I know it's been...
Forum: Extreme Speed Prop Planes
07-29-2003, 07:24 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

believe it or not!

Well, it's all Monocote! Yep, I was layed up with an injury So I sat there and did it..see what pain killers will do to your planes paint scheme!
Forum: Extreme Speed Prop Planes
07-29-2003, 09:09 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

new pic

Took a pic today while out flying the D/C F20 ..Now with a Jett .60..really something else..the speed is incredible!
Razor those doors look sweet!
Forum: Extreme Speed Prop Planes
07-13-2003, 11:47 PM
Replies: 450
Views: 48,137
Posted By flyrcjets

D/C Canopy

Wondering if any of you have a spare canopy you'd part with? I'd gladly pay for it as mine blew off today and we could'nt find it! Fastest it ever flew ..(with a Jett .60) thanks K
Forum: Extreme Speed Prop Planes
07-08-2003, 05:44 AM
Replies: 450
Views: 48,137
Posted By flyrcjets

D/C F20

Hey great thread! I'm really happy with my D/C F20. Just changed out a Jett 50 for a Jett 60..awesome..the plane is bashed as I lengthend the nose, added retracts, and a nose gear door. I covered the...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.