Rull

Thank you, guys.
All parts made in Solidworks 2009 , so I can send all project via e-mail.
It is a lot of work to make dimenthion list of all parts.
Ray, I use copper bushing for steel rods to prevent friction. Abit lubrication there.

BACKEMF

I have to go get parts to build a new pc today. Then I can re=install solidworks and maybe....

I've been without a decent pc to do 3d drafting too long. This is what I do for $$ too.

Dimensions I will work out my self then, once I'm up and running. thanks for the drawings, superb!

ryan_t888

SolidWorks is one of the best programs I have ever used. I get more hours per day, 5/7 days per week, using SolidWorks then sleeping.

Ryan

Rull

yes, nice soft.

Bad news. Accus turnigy 5000 5S 30C are arrived. They are wider then in specification. 42,5mm against 39mm. Cant put them in sponsons



<hr /><hr />

wave waker

nice SW there Rull[sm=thumbup.gif]...i got stock from learning it...

gen3v8

My Feedback: (1)

Rull your a top BOATER and i have not forgotten your requests. My Mother passed away and I have been upset and preoccupied.

BACKEMF

Ahhh, that is bad Serge! This happens allot at Hobby City.

That is why I decided to use 3S and 4S and 2800 kv 4pole motors, space is limited.

Maybe 4000Mah will fit. Sorry to see this happen, that would have been nice run time too, low amps higher voltage. Nice.

Rull

4000 5S will fit.
I have an idea reassembly pack and make 4S in sponson + 1 on brige.

BACKEMF

I was thinking almost the same thing.

I think I will try to put my akkus in the sponsons too, better stability.

BACKEMF

If I had noticed earlier in my shopping that you used 11L motors and 5S akkus, I may have followed you in power plant.

You spent much less than I did on motors. I still may try 5S too but with UL-1 Aquacraft motors.

What props were you thinking of running?

Rull

Hi Ray!
5S for my 11L motor is a lot of power. Normaly should be 4S for fun. But I want some more in speed :-)
The props are pairs L,R of Octura X442 and Graupner 40mm

BACKEMF

Yes.... Speed! that is what we want with our kitties

Rull

The hull a bit cuted. 5A5S li-po are in sponsons now! Need wedge in the front of hatch between brige and deck to support deck.

BACKEMF

OOooh yeah just a sneek peek at the hardware. Serge you are a TEASE!!! LOL...

That is just beautiful man!![X(]

BACKEMF

I'm just waiting for my carbon kevlar from HC, then I will build mine!

Rull

shafts assembly

BACKEMF

Hi Serge, what is the small diameter for in the middle of each steel shaft?

Does it hold lubrication?

Rull

Hi Ray!
It is for securing screw.
It is for saving shaft and props in case of braking flex shaft.
It is the same as the photos

BACKEMF

Serge, take a look!

http://www.hobbycity.com/hobbycity/s...idProduct=8521

Rull

Hi Ray!
Yes, I`v saw it. They are huge, and they haven`t place for the rope.
I try to show you main dimensions in millimeters

BACKEMF

Thank you Serge, those dimensions will be perfect, that is all I require.

srt10

My Feedback: (20)

Rull, have you measured your COG on this hull yet?
to me it looks to far forward with the batteries in front of the motors...
it could be around 40% or more

Rull

Not yet, but I think all ok.

srt10

My Feedback: (20)

I would start my COG on this hull at 35% to get a feel for it then moved to 30% and less once it's set up good..
the batteries do put alot of weight forward, and can produce alot of drag on the hull, pulling more amps than needed

Rull

today I`v found COG. It is between 27 and 30%. Can`t do 27 but 28% have without additional weight. So all as I wish.