Looking for 8mm - 1/4" stepped prop shafts ( RCMK or MTC )
Like header states ... seeing if ANYONE these shores has any inventory of the H.D. 8mm prop shafts stepped to 1/4" having a 1/4" cable hole in the other end. ( need 1 .. would by 3 ) Worst case will have to source from Europe or Asia ... figured asking here first :eek: |
RE: Looking for 8mm - 1/4
|
RE: Looking for 8mm - 1/4
Scott , You can email this guy and he will make you whatever you need .
http://rcraceboat.com/Storewiredrive.html |
RE: Looking for 8mm - 1/4
Scott,
I should have two complete RCMK new flex shafts. They use a special drive dog and I might have one of those also. I will look tomorrow. Thank you, Daniel |
RE: Looking for 8mm - 1/4
ORIGINAL: idocdave09 Like pictured here (just the shaft part) http://www.whhonline.com/PhotoGaller...ductCode=RMB95 Shaft I'm looking for are 1/4" at prop shaft, then step up to 8mm for the entire length of bearing surface then have a 1/4" female hole in the end to SOLDER your cable into ... which will be in my case a Square end cable running in a square drive collet at engine. |
RE: Looking for 8mm - 1/4
contact arrowmodelsport.com he would make you one but he's in the uk ! does a nice stinger and billet engine his site is new and has ony got an engine on it at the moment
|
RE: Looking for 8mm - 1/4
WHH has them that are 5/16 at one end for the cable to be soldered it the rest is turned down to 1/4 with 1/4 NF thread for the prop nut
ORIGINAL: Scott Schneider ORIGINAL: idocdave09 Like pictured here (just the shaft part) http://www.whhonline.com/PhotoGaller...ductCode=RMB95 Shaft I'm looking for are 1/4" at prop shaft, then step up to 8mm for the entire length of bearing surface then have a 1/4" female hole in the end to SOLDER your cable into ... which will be in my case a Square end cable running in a square drive collet at engine. |
RE: Looking for 8mm - 1/4
We need the larger diameter threw the bearing areas, running 75/85 mm props 1/4" bearings are getting beat to death, thus WHY wanting the bigger 8mm stuff ;)
ORIGINAL: idocdave09 WHH has them that are 5/16 at one end for the cable to be soldered it the rest is turned down to 1/4 with 1/4 NF thread for the prop nut ORIGINAL: Scott Schneider ORIGINAL: idocdave09 Like pictured here (just the shaft part) http://www.whhonline.com/PhotoGaller...ductCode=RMB95 Shaft I'm looking for are 1/4'' at prop shaft, then step up to 8mm for the entire length of bearing surface then have a 1/4'' female hole in the end to SOLDER your cable into ... which will be in my case a Square end cable running in a square drive collet at engine. |
RE: Looking for 8mm - 1/4
|
RE: Looking for 8mm - 1/4
Ah, the threaded on drive dog shafts :D .... yea thats the basic set-up. Tho looking for shafts only to solder sq drive cable into.
Looks like some of my European buddies are willing to set me up with some parts and pieces like shafts, bearings, struts etc better suited for twin abuse duty ..... just have to figure out what selection of parts shared so far best suits what I'm after. |
All times are GMT -8. The time now is 05:01 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.