|
((BIG-CRAWLER)) NB-JEEP 1/6-MODS . Last 3 Post =Test winch on the wall .
HELLO .. I owns one, JEEP 1 / 6 NEWBRIGHT ..
The rc-toys, can become rc-toys more efficient, giving them some mods. I present you ... ((( BIG-CRAWLER ))) ..STOCK/JEEP 1/6 NEWBRIGHT .. http://i346.photobucket.com/albums/p...G_0001-6-2.jpg I will begin very soon the mods .. THANK .. PS ... Excuse my words, I work with a translator .. I am QUECECOIS ..:D I love this crawler .. http://i346.photobucket.com/albums/p...ay20Rock-1.jpg |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
good to have you aboard texx great model look forward to your mods ..:D:D:D;)............http://i406.photobucket.com/albums/p...CRIM0003-9.jpg
|
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
THANK .. yaleforscale .. I will begin my mods ..
With the installation of metal/bearing in the differential .. http://i346.photobucket.com/albums/p...0007rrrr-1.jpg THANK |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
thanks texx these steel roller bearings make a big difference ....;);):D
|
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
HELLO ..
These are the items that I buy on EBAY .. Congratulations TEXX .. the item is yours. Please pay now! :D http://i346.photobucket.com/albums/p.../da50_12-1.jpg ################################################# + (1) Body only JEEP 1/6 ... NEWBRIGHT .. http://i346.photobucket.com/albums/p...efe1_3-1-1.jpg + (2) frame with diff .. http://i346.photobucket.com/albums/p...G_0028-1-1.jpg And do not miss parts ..:) ############################################ The metal/bearing are very important .. this will be my first mod .. I prepare the ground .. I have not locked the front diff, the former owner had done the work .. The rear is already locked by the company .. I opened the diff .. REAR DIFF .. http://i346.photobucket.com/albums/p...G_0011-2-2.jpg This gear has two small plastic bearing, I will instead set up two metal / bearing .. http://i346.photobucket.com/albums/p...G_0018-2-1.jpg FRONT DIFF ... I opened the diff .. I put some flat washer (spacer) to remove some loose gears .. FRONT and REAR .. http://i346.photobucket.com/albums/p...IMG_0030-1.jpg FRONT DIFF ... http://i346.photobucket.com/albums/p...G_0031-2-1.jpg Everything is ready to receive the metal / bearing http://i346.photobucket.com/albums/p...IMG_0045-1.jpg (4) little metal/bearing 3x8x3 .. http://i346.photobucket.com/albums/p.../index-1-1.jpg http://i346.photobucket.com/albums/p...G_0004-8-1.jpg (10) big metal/bearing/6x12x4mm .. http://i346.photobucket.com/albums/p..._0002-12-3.jpg I start the installation of metal/bearing .. The 4 large bearing is not difficult to install in each diff .. ..BEFORE .. http://i346.photobucket.com/albums/p...IMG_0011-1.jpg ..AFTER .. http://i346.photobucket.com/albums/p...G_0006-5-2.jpg http://i346.photobucket.com/albums/p...G_0017-2-1.jpg http://i346.photobucket.com/albums/p...G_0008-4-2.jpg http://i346.photobucket.com/albums/p...IMG_0014-5.jpg http://i346.photobucket.com/albums/p...G_0017-1-2.jpg http://i346.photobucket.com/albums/p...G_0011-2-4.jpg http://i346.photobucket.com/albums/p...G_0020-3-1.jpg http://i346.photobucket.com/albums/p...G_0022-1-1.jpg I also enlarges the center of this small gear, with a little grater .. The 2 small bearing, were placed without difficulty .. I greased the main parties, and close the diff / rear .. http://i346.photobucket.com/albums/p...G_0023-1-1.jpg I then cut the surplus pivot / axis .. http://i346.photobucket.com/albums/p...G_0031-2-2.jpg I lubricate the parts and reinstall the diff / rear .. http://i346.photobucket.com/albums/p...IMG_0033-1.jpg http://i346.photobucket.com/albums/p...G_0034-2-1.jpg http://i346.photobucket.com/albums/p...G_0027-2-1.jpg In a few days, I'll do the same work on the front/diff .. These metal/bearing, certainly help to slow the wear of these shaft/axis .. ..THANK .. |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
texx great work your the master modder love it ..:D:D:D:D:D:D:D:D:D:)
|
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
yaleforscale THANK .. For the commentary ..
The mods will follow next week .. I work this weekend .. THANK .. I love this (( crawler ))[8D];) http://i346.photobucket.com/albums/p...4YFZLPVG-1.jpg |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
The next mod will be installing a (home/made) WINCH ..
In the belly of the beast ((BIG-CRAWLER)) :) (( INSECTOR parts) ) for winch .. Very strong motor .. Very strong gearing box .. http://i346.photobucket.com/albums/p...IMG_0005-5.jpg This winch is really very powerful .. :D The INSECTOR rc ... http://i346.photobucket.com/albums/p...G_0006-4-1.jpg Parts of rc toy-used, can (occasionally) to help us tremendously .. :D |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
Cool crawler Texx, it should be very tough once all your mods are completed [8D]
|
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
great work texx as always .. ;)
|
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
yaleforscale .. cobra69 .. THANK ..
I will start the mod ((BIG/WINCH/INSECTOR )) for .. BIG/CRAWLER) next week .. :) This winch, certainly help to get out of the wrong places.:D http://i346.photobucket.com/albums/p...ep-winches.jpg |
RE: NEWBRIGHT JEEP 1/6 MODS (LOULOU)
HELLO ..
I did a little test, just to assess the strength of my future ((WINCH)) My LAND ROVER, (with 2 battery) at a weight of 13 lbs .. The winch is behaving very well .. it is very strong .. Without fatigue, it raises my LAND ROVER, above the floor .. I have to make a support .. and developed a plan to install on my ((BIG-CRAWLER) [youtube]http://www.youtube.com/watch?v=u8_IP_L7kOw[/youtube] ################################################## ### I put all my efforts on the BIG-CRAWLER, so that it is a good climber.. If BIG-CRAWLER stuck, it would depend may be without the help of another crawler .. :-) http://i346.photobucket.com/albums/p...DS/W0103-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
Buy a rc/winch would have been good ..
http://i346.photobucket.com/albums/p...66244476-1.jpg but it would be installed in reinforcements and solidify anchorages bumper and frame .. And this work would have been very difficult .. I will rather choose to install this ( (HOME-MADE WINCH-INSECTOR )) inside the frame ....:D http://i346.photobucket.com/albums/p...29THH1_1-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I made some plans for the installation of the WINCH ..
I find this site, which seems to me .. The shaft of the winch, pass completely through the plastic/frame, from one side to the other .. http://i346.photobucket.com/albums/p...G_0020TT-1.jpg I cut both ends of shaft, and installed two strong plastic reinforcements at each end .. I still have to install a switch that works in both directions ((CENTER-OFF SWITCH TOGGLE DPDT)) I'll find this item at RADIO SHACK (THE SOURCE) .. http://i346.photobucket.com/albums/p...0439w345-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I solidify this winch ..
A piece of Plactic (tube), screwed into the floor of the frame under the motor, which prevents the motor back .. http://i346.photobucket.com/albums/p...G_0008-4-1.jpg And one screw to hold it in place. http://i346.photobucket.com/albums/p...G_0010-5-2.jpg At each end of the shaft, I screwed two pieces of plastic which solidify the shaft, which crosses the frame .. http://i346.photobucket.com/albums/p..._0002-12-1.jpg http://i346.photobucket.com/albums/p...G_0005-7-1.jpg These small pieces from the model 1/10 .. http://i346.photobucket.com/albums/p...G_0011-2-3.jpg ################################################## Small video showing the operation of the .. (( INSECTOR/ SWITCH/BIG-CRAWLER )) without switch :D:D:D It will operate with a 7.2 volt battery .. [youtube]http://www.youtube.com/watch?v=oIu0pAUkb4o[/youtube] http://i346.photobucket.com/albums/p...G_0004-7-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I have purchased my switch .. I chose the model which automatically returns to center .. DPDT 20-Amp Momentary Flip Switch
$ 4.59 us .. :) $ 7,99 CDN :( Model: 275-709 Enough switches to make you flip! Get things started with this DPDT momentary flip switchspring-loaded to return to the center off position. Rated 20 amps at 12VDC. http://i346.photobucket.com/albums/p...G_0012-1-1.jpg http://i346.photobucket.com/albums/p...IMG_0014-2.jpg I will keep your finger on the switch during its operation .. This will be a protection, not to break the wire .. http://i346.photobucket.com/albums/p...G_0009-3-3.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
Videos ....(( BIG-WINCH/INSECTOR/BIG-CRAWLER ))
[youtube]http://www.youtube.com/watch?v=S1zujWlIqp0[/youtube] The winch pulls my Land Rover, which is placed aside.(13 lbs) .. ((( The switch is now installed on the chassis (accessible via the floor) and not on the console .. ))) http://i346.photobucket.com/albums/p...IMG_0005-1.jpg [youtube]http://www.youtube.com/watch?v=rb_gio0h06A[/youtube] The winch pulls 2 chair (22 lbs) and I think I could pull the table also :D :D :) :) http://i346.photobucket.com/albums/p...IMG_0002-1.jpg [youtube]http://www.youtube.com/watch?v=3q4YdM4Onck[/youtube] ################################################## ###################### ..Hand ... [youtube]http://www.youtube.com/watch?v=D5bxQLn1a0o[/youtube] ..Lift YELLOW-CRAWLER .. [youtube]http://www.youtube.com/watch?v=oIUj-5ggZ5g[/youtube] ..Lift BIG-DRILL .. [youtube]http://www.youtube.com/watch?v=plIYE8Ot0As[/youtube] |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I do not know if I will keep this bumper ..
http://i346.photobucket.com/albums/p...G_0048-1-2.jpg http://i346.photobucket.com/albums/p.../e087_12-1.jpg A bumper (metal) smaller, with the roller / guide to install it would be nice .. http://i346.photobucket.com/albums/p...er124061-1.jpg This new bumper will be mounted directly to the frame .. http://i346.photobucket.com/albums/p...G_0012-1-2.jpg http://i346.photobucket.com/albums/p...G_0026-1-1.jpg I love this crawler ..:D:D http://i346.photobucket.com/albums/p...CF0973-1-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I got my neighbor, this material, which is very good for a bumper ..
http://i346.photobucket.com/albums/p...G_0019-5-2.jpg http://i346.photobucket.com/albums/p...G_0018-2-3.jpg I cut and installed temporarily at the place where it will be fixed. http://i346.photobucket.com/albums/p...G_0024-1-1.jpg http://i346.photobucket.com/albums/p...G_0025-2-1.jpg Perhaps I will paint in black .. and fix 2 small hook .. http://i346.photobucket.com/albums/p...b-1920-1-1.jpg http://i346.photobucket.com/albums/p...G_0003-5-4.jpg This bumper will be painted in (black) :D ################################################## http://i346.photobucket.com/albums/p...G_0025-3-1.jpg ..THANK .. |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I installed the (guide/roll) in plastic, it looks good ..
When I have a guide/roller metal, I install it .. The winch is functional .. THANK http://i346.photobucket.com/albums/p...G_0005-8-3.jpg http://i346.photobucket.com/albums/p...G_0006-6-1.jpg http://i346.photobucket.com/albums/p...G_0008-5-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
Remove this big body, had a ((BIG))job ..
I fixed this problem by installing plastic rods (solid plastic hanger) .. The body slips into its old anchors, and it remains in place .. It is set at the front and rear .. FRONT .. http://i346.photobucket.com/albums/p...ex/z01-2-1.jpg http://i346.photobucket.com/albums/p...utex/z02-1.jpg http://i346.photobucket.com/albums/p...utex/z04-1.jpg http://i346.photobucket.com/albums/p...utex/z05-1.jpg http://i346.photobucket.com/albums/p...utex/Z06-1.jpg http://i346.photobucket.com/albums/p...utex/Z07-1.jpg REAR .. http://i346.photobucket.com/albums/p...utex/X01-1.jpg http://i346.photobucket.com/albums/p...utex/X02-1.jpg http://i346.photobucket.com/albums/p...utex/X03-1.jpg The center of the body, has (2) anchors .. I'll screw a long screw (by cutting off his head) as anchors, and once inserted into its hole, I'll screw (2) nuts/ears by the underside of the frame .. http://i346.photobucket.com/albums/p...G_0004-8-2.jpg The body is very solid, and the time to remove it will be shorter .. and less stressful .. http://i346.photobucket.com/albums/p...ex/z03-2-1.jpg http://i346.photobucket.com/albums/p...G_0003-5-4.jpg This bumper will be painted in (black) :D ..THANK .. |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I lowered the roll/cage .. This gives him a look getter .. http://i346.photobucket.com/albums/p...G_0037-1-1.jpg I also remove some sticker .. The bottom of the door and also on the hood (those who were on the side) ) .. http://i346.photobucket.com/albums/p...G_0028-2-1.jpg http://i346.photobucket.com/albums/p...IMG_0043-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I lowered the body of some 3/4 inches ..
I could perhaps be reduced further (1/2 inches)? BEFORE .. AFTER .. http://i346.photobucket.com/albums/p...G_0123-2-1.jpg http://i346.photobucket.com/albums/p...IMG_0124-1.jpg BEFORE .. AFTER .. http://i346.photobucket.com/albums/p...IMG_0134-1.jpg http://i346.photobucket.com/albums/p...IMG_0003-1.jpg |
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
|
RE: ((BIG-CRAWLER)) NEWBRIGHT JEEP 1/6 MODS (LOULOU-TEXX)
I installed the 4 beadlock (plastic) :( directly on the rim ..
One day I might try, to produce metal .. :D The look seems to be a good .. http://i346.photobucket.com/albums/p..._0004-10-1.jpg http://i346.photobucket.com/albums/p...G_0008-7-1.jpg - I also removed the passenger-seat ((For individual crawling )) :) http://i346.photobucket.com/albums/p...IMG_0017-1.jpg http://i346.photobucket.com/albums/p...G_0015-1-1.jpg I pasted a sheet of plastic on the floor before installing the carpet. :D The relocation of the switch, is a good desicion .. The wire congestion is eliminated .. :D http://i346.photobucket.com/albums/p...G_0005-2-1.jpg |
| All times are GMT -8. The time now is 11:07 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.