1/6 SCALE TWIN OTTER BUILD
i am building this airplane for a friend of mine.its the 1/6 scale from john labelle plans.130inch wingspan.got finished going through all the pieces and sorting them out of the short kit...from what i see so far everything looks good. its not going to be a full blown to scale contest airplane...it will have some details and it is more meant to be an everyday flyer..
i will start posting some pics soon..so everyone interested please feel free to chime in whenever and enjoy gene |
RE: 1/6 SCALE TWIN OTTER BUILD
I'll be watching for updates. Please, give me a heads up prior to maiden flight. I'd like to be there.
gb |
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
ok here is the first few pics. decided to start with the horiz stab...the spars were made undersize and capped with balsa to ease in sanding to get the correct shape for the sheeting. it doesnt hurt any with strength.just makes sanding to shape much easier...if you look close at pics you will see what i am talking about...will show better when i get to that point
|
RE: 1/6 SCALE TWIN OTTER BUILD
in the first pic you will see the rear spar for horiz stab....it was made in 2 parts...reason for this is much easier to cut the slots for the elev hinges, and in the 2nd pic. shows the spar laminate glued and supported to an aluminum angle
makes it more stable and keeps the warps out |
RE: 1/6 SCALE TWIN OTTER BUILD
Nice start...Is this going to be a UV-18???Have not talked to BH in so long. Already forgot what powerplants are going in this bird??
|
RE: 1/6 SCALE TWIN OTTER BUILD
Electronic G-38's from the AC-47. Just fit inside cowling with the carbs sticking out. You should have seen the lumber box. P-40 is done so no.3 Skyraider is on the table. Doing Navy. Bought a project off of Ebay.
|
RE: 1/6 SCALE TWIN OTTER BUILD
gblass777, think this is your L-19, correct? http://www.youtube.com/watch?v=8v36aGuNiNc
SIMCO, give me heads ups before maidens. Your planes are always interesting. C-47 maiden at about 4:30: http://www.youtube.com/watch?v=8v36aGuNiNc Thunderbolt: http://www.youtube.com/watch?v=RxC5nEFupeY Skyraider at about 3:55: http://www.youtube.com/watch?v=p32W_GHQpqQ gb |
RE: 1/6 SCALE TWIN OTTER BUILD
yes jumper666..that is my L-19
|
RE: 1/6 SCALE TWIN OTTER BUILD
Knowing the quality of work you do, I can imagine how well the Otter will turn out.
gb |
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
elev halves almost ready for top skin. then horiz stab alignment..hinged with aluminum tubing and carbon fiber rod
|
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
elevs connected to horiz stab for hinge alignment...elevs will stay removeable until horiz stab is mounted to vertical...so far everything is fitting nicely
|
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
Posting these for gblas777
gb |
RE: 1/6 SCALE TWIN OTTER BUILD
Looks great.
I will be following along too. Any plans to build some floats ? |
RE: 1/6 SCALE TWIN OTTER BUILD
been thinking about floats...might build in the hard points for the floats. in the early build stages.....very doable
|
RE: 1/6 SCALE TWIN OTTER BUILD
Great! I have the kit on the back burner as well, will be following with interest!!
|
RE: 1/6 SCALE TWIN OTTER BUILD
Flying with floats will be impressive.
gb |
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
in these pics are the plate for the main gear. 6 of the eight slots had to be extended to match the other 2 for proper fit on bulkheads...also cut the bevel on the sides to match the contour of the fuse skin..much easier to do that before it is glued in. you can see in the pics the before and after
|
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
here is the main landing gear plate fitted; and glueing in place. slow setting epoxy used to allow time to make sure everything is all square and set right
|
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
a few pics of the stabs....started fitting vert stab and checked the fit of horiz stab...so far everything is fitting nice
|
RE: 1/6 SCALE TWIN OTTER BUILD
Coming along nicely.
gb |
RE: 1/6 SCALE TWIN OTTER BUILD
Subscribing,I have Johns kit as well and will follow with interest,I'm finishing up some other projects and hope to start soon on this one ,keep up the good work...
Steve |
RE: 1/6 SCALE TWIN OTTER BUILD
I'm interested in this plan but can't get on John's website (www.johnsplansandkits.com). Are the plans and kits still available?
|
RE: 1/6 SCALE TWIN OTTER BUILD
yes i think the plans and kits are still available....the one i am building was cut and shipped a few weeks ago...i havent heard anything different...................been working on horiz stab and rudder....it takes a little time since it is built on the airplane and not over the plans...will have some more pics soon
|
RE: 1/6 SCALE TWIN OTTER BUILD
1 Attachment(s)
ok heres a few more pics...getting everything aligned with the verticle stab and rudder........little slow going here....measure twice and cut once rule applies...had to make the rudder spar measuring off the back of the vert spar .....need to sand down the tail sectionto get ready for some sheeting so it is time to make a temp move to the garage....sawdust in the house is a nono with the wife.....balsa dust seems to get everywhere...have to agree with her
|
RE: 1/6 SCALE TWIN OTTER BUILD
I saw a float company that would be interested in cutting foam for the floats. Let's put in the hard points SiMCO
|
All times are GMT -8. The time now is 03:02 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.