Official HPI Savage Flux XS thread...
#2252
Join Date: Jul 2008
Location: Cambridge,
ON, CANADA
Posts: 3,107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Good point, length is very important.
My way of handling things is similar to TBJ's: a spectrum setup with a ~2 inch receiver wire that stays in the radio box and there have been no range issues. Some people have just mounted the wire off of the radio box by drilling a hole (check a few posts back).
#2253
Senior Member
My Feedback: (9)
Join Date: Sep 2010
Location: London,
ON, CANADA
Posts: 143
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
I just ran my wire up over the tranny to the RX Kept tight with a zip tie and I keep the actual antenna wire with the tube cut to proper length under the body never had any range problems.
#2254
Join Date: Jan 2012
Location: Los Angeles, CA
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
I noticed that the Hot Racing front c-hubs don't stop the steering knuckles from turning where they should, and end up allowing the wheels to turn so far that the dog bone comes out, causing them to snap. I also was wondering for a while why that was the only Hot Racing part for the Savage XS that Toadz RC doesn't carry, and now I am suspecting this has something to do with it. Has anyone here used them and experienced this problem?
Also, has anyone here tried the sway bar for this truck? I'm wondering if it is really worth buying.
Also, has anyone here tried the sway bar for this truck? I'm wondering if it is really worth buying.
#2255
Senior Member
My Feedback: (4)
Join Date: Aug 2011
Location: horseheads, NY
Posts: 2,643
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Welp, finally got my Flux XS last night! Got it from my buddy finally. $200 RTR with 2s lipo and venom procharger ( charger doesnt work right) he only ran it twice, so there is very minimal scratches oon the roof. it still smells new!! maybe ill post pics of it tonight. I've already got planned new tires and rims, new high torque servo and new charger and lipo for it.
#2256
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
ORIGINAL: gdiddy13
Speaking of antenna wires! My tube has come out, and so did the screw that helped hold it in place. Also my wire has been worn down a bit and it dangerously close to the drive shaft.
What have you guys done to keep it out of the way, and the tube in place?
Speaking of antenna wires! My tube has come out, and so did the screw that helped hold it in place. Also my wire has been worn down a bit and it dangerously close to the drive shaft.
What have you guys done to keep it out of the way, and the tube in place?
#2258
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
HPI needs to go back the drawing board with the cups on the axle shafts.. Here is what the one on the left front side of my son's XS looks like after 5 months of bashing...
The one on the left is from the right side of the XS and the other is from the side
Also her is what the bearing looked like when I took it apart..
And here are the only balls that were left in the bearing.
Here is the upright from the left side.
The one on the left is from the right side of the XS and the other is from the side
Also her is what the bearing looked like when I took it apart..
And here are the only balls that were left in the bearing.
Here is the upright from the left side.
#2260
Join Date: Jul 2008
Location: Cambridge,
ON, CANADA
Posts: 3,107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
Dspdrew - are the sway bars available yet?
Congratulations Cummins.. Enjoy the truck. You are past the initial fear of it blowing up the first moment the ESC sees power.
#2261
Member
Join Date: Dec 2011
Location: , OH
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: t9dragon
Are you refering to the hole in the receiver box?
ORIGINAL: gdiddy13
So it just lays there? I know this is a really simple process I'm sure, but do you have a pic?
So it just lays there? I know this is a really simple process I'm sure, but do you have a pic?
Yea, well the whole setup. Are you not using the tube at all then?
#2262
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
ORIGINAL: nitro-rob
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
Dspdrew - are the sway bars available yet?
Congratulations Cummins.. Enjoy the truck. You are past the initial fear of it blowing up the first moment the ESC sees power.
I am going to replace the ones on my XS when I get my new front diff this week.
#2264
Senior Member
My Feedback: (4)
Join Date: Aug 2011
Location: horseheads, NY
Posts: 2,643
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: nitro-rob
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
Dspdrew - are the sway bars available yet?
Congratulations Cummins.. Enjoy the truck. You are past the initial fear of it blowing up the first moment the ESC sees power.
#2267
Member
Join Date: Dec 2011
Location: , OH
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
that's a great idea!. did you seal the hole back up with anything?
ORIGINAL: t9dragon
Here are the pics you asked for..
ORIGINAL: gdiddy13
Yea, well the whole setup. Are you not using the tube at all then?
Yea, well the whole setup. Are you not using the tube at all then?
#2269
Senior Member
My Feedback: (4)
Join Date: Aug 2011
Location: horseheads, NY
Posts: 2,643
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Finally got some pics of the Flux i just got. $200 for the truck, procharger and 2s lipo. only ran twice. Boy do i have plans for this thing. my orders should be in next week. ill post update pics.
#2270
Join Date: Jan 2012
Location: Los Angeles, CA
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: nitro-rob
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
T9, my friends did the same thing within the first pack. He is an animal with his trucks but thats even too quick for him.
Dspdrew - are the sway bars available yet?
Congratulations Cummins.. Enjoy the truck. You are past the initial fear of it blowing up the first moment the ESC sees power.
#2271
Junior Member
Join Date: Sep 2002
Location: lapeer,
MI
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
I got a new antenna from Hpi and connected it on board to the receiver. Still little range. Any good radio replacements?
#2273
Senior Member
Join Date: Sep 2011
Location: Mississauga, ON, CANADA
Posts: 107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: starjammir
I got a new antenna from Hpi and connected it on board to the receiver. Still little range. Any good radio replacements?
I got a new antenna from Hpi and connected it on board to the receiver. Still little range. Any good radio replacements?
#2274
Join Date: Jul 2008
Location: Cambridge,
ON, CANADA
Posts: 3,107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
The spectrum is a good idea because they have a range of radios that will work with the same receiver so you have good upgrade potential.
#2275
Junior Member
Join Date: Jan 2012
Location: Concepcionbio-bio, CHILE
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Hey guys,
has anyone got this problem? After about 15 minutes of running, the throttle wont response and it wont move at all, but you can still make the wheels move. The wheels turn perfectly but theres no response to the throttle at all. Also, ive been having some issues with the front wheels, they move quite alot making it hard to control.
Thanks, Diego
has anyone got this problem? After about 15 minutes of running, the throttle wont response and it wont move at all, but you can still make the wheels move. The wheels turn perfectly but theres no response to the throttle at all. Also, ive been having some issues with the front wheels, they move quite alot making it hard to control.
Thanks, Diego