RE: AKM SU-27 Flanker-Does Look Good
1 Attachment(s)
Here is a pic for you
Pete |
RE: AKM SU-27 Flanker-Does Look Good
DOOOOOOH crap I figured it out ..... to late a night last night ... the notch goes to the former where the fin joins. sheeehs
Pete |
RE: AKM SU-27 Flanker-Does Look Good
Did you guys have to widen your sheeting too...? My top sheeting was slighly too narrow for a proper fit in some places...
I also noticed on the pics on the CD that Alex widened his sheeting slightly too. |
RE: AKM SU-27 Flanker-Does Look Good
Yep the sheeting by the back fins are just off a tic and will need to added in ... it was the same way on the the MIG as well ... I also found that when you line up the stab to be flush with F8 that the back of the stab does not meet with F9 ...seems to be short by 1/16" all the way across ....after double checking that the formers are right on to the plan and that the stab was flush to F8 I had to add to it so it would marry to F9 ...Hmmmmm ooooh well.
Pete |
RE: AKM SU-27 Flanker-Does Look Good
I had to splice on another 1/8" or so on both of the top deck sheeting on the MiG29. I haven't started the SU yet, so I can't speak for that kit.
Don |
RE: AKM SU-27 Flanker-Does Look Good
Blade!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I just looked at the pic you posted... I see you haven't sanded your "center fuse" yet... Do it now before you start sheeting!!!!!!! Or there will be hell to pay later... It takes a lot of sanding, and if you can't get to it properly it will be a horrible job to do... |
RE: AKM SU-27 Flanker-Does Look Good
I "believe" that tick I see in your picture belongs by the front of the vertical fin
ORIGINAL: Blade47 Here is a pic for you Pete |
RE: AKM SU-27 Flanker-Does Look Good
Yep thanks Rudeboy ... I was just test fitting the sheeting and I mark the sheeting to side of the fuse before I start to sand :D makes for a nice fit.
Pete |
RE: AKM SU-27 Flanker-Does Look Good
1 Attachment(s)
You may want to do what Don ( this is Dons picture from the MIG build) and I did on the MIG aft sheeting ... put 1/16 x 1/8" shelf around the inside for the sheeting to rest on ... keeps it from pushing in ;)
Pete |
RE: AKM SU-27 Flanker-Does Look Good
1 Attachment(s)
I haven't been doing much with this lately other than painting it.
|
RE: AKM SU-27 Flanker-Does Look Good
what sorta paint ya using ??
|
RE: AKM SU-27 Flanker-Does Look Good
1 Attachment(s)
I threw the unfinished wings on and the canopy to see how this is looking. Fuse is a Charcoal Metallic and the wing will be gray near the fuse and white toward the outside
Rust Oleum with a Glosss clear coat over it. It came out okay. |
RE: AKM SU-27 Flanker-Does Look Good
I like the paint job Snoop---- going to look wild when done for sure. [X(] going 130 MPH just setting there :D
|
RE: AKM SU-27 Flanker-Does Look Good
Snoop... I see you did not cover the "engine humps" at the back of the plane... looks kinda weird with those cutouts visible...[X(]
|
RE: AKM SU-27 Flanker-Does Look Good
i think those are the access hatches
|
RE: AKM SU-27 Flanker-Does Look Good
ORIGINAL: bob27s i think those are the access hatches |
RE: AKM SU-27 Flanker-Does Look Good
Snoop! Q for you ---- the sheeting for the LEX ...did you fill in the gap between the fuse sides and the LEX sheeting? I had look at Alex's SU and looks to me that he did not ... seems to be unfinished that way.
And by chance do you ( or anyone reading this) know what the air pressures reading should be on the spring air 101HD air tank when it is full? |
RE: AKM SU-27 Flanker-Does Look Good
today when i got home from work I found my package from AKM, the SU-27 has finally arrived...gee I guess this puts me pretty far behind everyone else..:eek:.. guess I'll just have to perservere.. and by the time I clear out my workshop , setup my equipment make a bench..blah blah blah..well at least I hope to see vid's of the ones you guys are/have put together.. I'll need the inspiration..
|
RE: AKM SU-27 Flanker-Does Look Good
I have a answer to my second Q from Spring Air and for others that want to know. :D
"We run our retracts between 80 to 90 psi. You can go higher but we find the air lines start to come off the fittings. Bill Watton Spring Air" |
RE: AKM SU-27 Flanker-Does Look Good
I sanded a "bevel" type angle their to make it flush with the side of the fuselage, Then ran down the line of it with that balsa filler stuff
ORIGINAL: Blade47 Snoop! Q for you ---- the sheeting for the LEX ...did you fill in the gap between the fuse sides and the LEX sheeting? I had look at Alex's SU and looks to me that he did not ... seems to be unfinished that way. And by chance do you ( or anyone reading this) know what the air pressures reading should be on the spring air 101HD air tank when it is full? |
RE: AKM SU-27 Flanker-Does Look Good
Thanks Snoop
|
RE: AKM SU-27 Flanker-Does Look Good
I did that someplace else too. I think it was the ailerons.
|
RE: AKM SU-27 Flanker-Does Look Good
Cool ---- what I did was sheet the top of the ailerons with 1/16" and sheeted all of the wings as well as it is hard to cover in two tone color.
|
RE: AKM SU-27 Flanker-Does Look Good
I finished the wings and started the fuselage yesterday. I'll post the mods required to use oleo's as I go once I figure out how to post pictures! Has anyone flown their su-27 yet?
mike |
RE: AKM SU-27 Flanker-Does Look Good
Mike, hit reply in this box (not the one at the end of the thread). You'll see "Click here to upload" in the lower left of the reply box. You can then upload up to 4 pictures from your harddrive as long as the aggregate size of all the pics you post is less than 3 meg.
After it finishes loading (may take a while depending on your connection speed) it will say it was successful. Close the box and hit "OK" and you're all done. Don ORIGINAL: picard1 I finished the wings and started the fuselage yesterday. I'll post the mods required to use oleo's as I go once I figure out how to post pictures! Has anyone flown their su-27 yet? mike |
All times are GMT -8. The time now is 01:09 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.