RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: glowstart
Showing results 1 to 19 of 19
Search took 0.61 seconds.
Forum: Scratch Building, Aircraft Design, 3D/CAD
07-16-2009, 08:17 PM
Replies: 11
Views: 5,871
Posted By glowstart

RE: Golden Era 60 Bipe

Thanks w8ye
Forum: Scratch Building, Aircraft Design, 3D/CAD
07-16-2009, 08:10 AM
Replies: 11
Views: 5,871
Posted By glowstart

RE: Golden Era 60 Bipe

It's pretty fast for a biplane, fly on half throttle most of the time. Almost unlimited vertical climb. Great sound. Designer Fred Randall used carbon fibre rods for wing spars, I used the standard...
Forum: Scratch Building, Aircraft Design, 3D/CAD
07-15-2009, 07:22 PM
Replies: 11
Views: 5,871
Posted By glowstart

Golden Era 60 Bipe

Completed last month this biplane version of the Golden Era 60 Biplane from Model Aviation. Biggest change was moving the servos to the tail to offset the weight of the Saito 120, also moved the...
Forum: Futaba Radios Direct support forum
04-30-2009, 05:51 PM
Replies: 3
Views: 532
Posted By glowstart

T6XA - 7CAP TX Crystal Interchangable?

I am purchasing a slightly used 7CAP transmitter with a crystal frequency incompatable with my receiver crystal frequency channel 57 . Can I swap the crystal from my broken T6XA into a 7CAP?
Forum: Glow Engines
08-31-2006, 11:08 AM
Replies: 54,891
Views: 5,433,399
Posted By glowstart

RE: Welcome to Club SAITO !

I am a proud owner of a new 150, putting it in a GB Sukhoi. Question: when the motor is mounted to the right, the NV faces the bottom. Any issues removing the carb body and rotating it 180 degrees so...
Forum: O.S. Engines Support
02-21-2006, 07:05 PM
Replies: 3
Views: 677
Posted By glowstart

RE: 46FX Run Problems

This engine has the remote needle valve attatched to the rear cover. Could the same situation occur with this set-up? Looking at the old needle valve closely, there are small gouges and marks...
Forum: O.S. Engines Support
02-21-2006, 12:32 PM
Replies: 3
Views: 677
Posted By glowstart

46FX Run Problems

I have a 46FX that is several years old with probably a 1000+ tanks of fuel thru the carb. Over the past year, I noticed that the engine will only run well if the needle valve is tuned out about 1/3...
Forum: Questions and Answers
11-03-2005, 12:29 PM
Replies: 1
Views: 502
Posted By glowstart

RE: MC Modeler plans service

I ordered a set of RCM plans in September, and they were delivered first week in October. If they are currently taking orders, cannot say. But I know they are not shipping any RCM back issues,...
Forum: Kit Building
06-17-2005, 11:33 AM
Replies: 189
Views: 23,308
Posted By glowstart

RE: What Kit would you like to see brought back?

SUPER AEROMASTER
Forum: Kit Building
01-15-2005, 11:18 AM
Replies: 8
Views: 1,701
Posted By glowstart

RE: Global Raven

Any comments about the Raven? Personnel experiences? When I get to it, will most likely put in a 91fs since it seems like it may be a little tail heavy and could use some weight up front. It's a nice...
Forum: Kit Building
01-12-2005, 02:34 PM
Replies: 8
Views: 1,701
Posted By glowstart

RE: Global Raven

I tend to like the more aerobatic planes of this size. Thought this would be a challange with a low investment. I have no problem flying without a cowl. but since it is a mid-wing plane, the canopy...
Forum: Kit Building
01-12-2005, 12:41 PM
Replies: 8
Views: 1,701
Posted By glowstart

Global Raven

Just purchased a 62" Global Raven at a local swap meet dirt cheap. Nice looking plane and the builder was a real craftsman. It looks like it was never flown, and is 90% complete. I discovered later...
Forum: Kit Building
12-09-2004, 12:34 PM
Replies: 112
Views: 23,000
Posted By glowstart

RE: Top Flite Contender

I've just finished the fourth summer with mine, it's one of my favorite planes. One great trick is to drop the flap around 50 degrees and do a steep carrier landing, flaring it right before...
Forum: ARF or RTF
12-07-2004, 12:32 PM
Replies: 49
Views: 3,590
Posted By glowstart

RE: Vectorflight Edge 540 on the way, any building tips

I too have the 91FX in my Edge, although it has excellent vertical, it is not unlimited. Just wondering Horace35, what prop combo are you using to accomplish the hover? I don't have an accurate...
Forum: Questions and Answers
07-29-2004, 04:11 PM
Replies: 3
Views: 570
Posted By glowstart

RE: What plane?

Looks like a Neptune
Forum: ARF or RTF
07-15-2004, 11:15 AM
Replies: 26
Views: 2,595
Posted By glowstart

RE: VectorFlight On Sale!

Well Crash Master, VF quote ' The gap between the wing root rib and the fuseledge side has been eliminated from the top side by curving the TE inwards to match the fuseledge contour. However, there...
Forum: ARF or RTF
07-14-2004, 03:36 PM
Replies: 26
Views: 2,595
Posted By glowstart

RE: VectorFlight On Sale!

Got a response back from Vectorflight explaining that they have most of the wing gap situation licked, along with a few other improvements.
Forum: ARF or RTF
07-12-2004, 11:27 AM
Replies: 26
Views: 2,595
Posted By glowstart

RE: VectorFlight On Sale!

Had a VF Edge last year until I piled it into tera firma doing a low level knife edge. One item that bothered me about it, however, was a wing root gap going towards the trailing edge. Does anybody...
Forum: Kit Building
06-23-2004, 01:25 PM
Replies: 9
Views: 1,244
Posted By glowstart

Hog Bipe or ultimate?

I'm trying to decide between the two and not sure which way to go. I've owned 60 size Extra's and Edges, and this would be my first bipe for a winter project. I like to hot dog around and do pattern...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.