RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: kebuttke
Showing results 1 to 20 of 20
Search took 0.38 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
11-18-2011, 06:25 AM
Replies: 4,979
Views: 915,373
Posted By kebuttke

RE: New Hitec Aurora 9-Channel 2.4Ghz Radio System

hello! had a question about the switch and slider reassignments. can the left slider be assigned to throttle and the left stick then assigned to control servos for pan and tilt? also, i havent really...
Forum: Brushed/Brushless motors, speed controls, gear drives
01-24-2011, 02:44 PM
Replies: 6
Views: 3,026
Posted By kebuttke

RE: emax bl2826/06

i figure it is kinda the same as the difference between ford and honda. one will run 200,000 miles, the other will need a new engine at 100,000. (honda runs longer, i have owned both) it is my first...
Forum: Brushed/Brushless motors, speed controls, gear drives
01-24-2011, 12:27 PM
Replies: 6
Views: 3,026
Posted By kebuttke

RE: emax bl2826/06

it is going on a queen bee flying wing for fpv
Forum: FPV, UAV & Drones
01-24-2011, 07:21 AM
Replies: 6
Views: 1,139
Posted By kebuttke

RE: Interference avoidance

So how can I determine which freqs will cause trouble?
Forum: Foamies! - RC Electric Foam Aircraft
01-24-2011, 05:57 AM
Replies: 0
Views: 817
Posted By kebuttke

queen bee 100 inch

i looked and could not find anything on this, so i apologize if it has been covered previously. the outboard wing sections of the queen bee are removable. fairly common knowledge. what i havent been...
Forum: Brushed/Brushless motors, speed controls, gear drives
01-24-2011, 01:43 AM
Replies: 6
Views: 3,026
Posted By kebuttke

emax bl2826/06

just want to post this for anyone else using or considering this motor as i couldn't find much on it myself. have not installed in plane yet, attached to a 5kg digital kitchen scale with a towerpro...
Forum: Foamies! - RC Electric Foam Aircraft
01-23-2011, 07:28 AM
Replies: 2
Views: 683
Posted By kebuttke

gyro rudder

would a rudder connected to a gyro be a good idea to counteract yaw oscillations or cross winds? this would be standalone i.e. connected to a battery and not to the receiver and mounted on a queen...
Forum: Model Rockets & Rocketry
01-21-2011, 05:41 AM
Replies: 5
Views: 3,178
Posted By kebuttke

RE: jato bottles

It should be possible, but it is something that you would want to fall off or be jettisonable after takeoff. Two motors would be easier to balance, thrust-wise, but you may have a problem getting...
Forum: FPV, UAV & Drones
01-21-2011, 02:44 AM
Replies: 6
Views: 1,139
Posted By kebuttke

RE: Interference avoidance

Which is perfect because I am stationed in south Korea.
Forum: FPV, UAV & Drones
01-20-2011, 08:17 AM
Replies: 6
Views: 1,139
Posted By kebuttke

Interference avoidance

Which of these freqs won't affect 2.4ghz? They are all ghz.

8 channel operation ( PLL) (1.080 - 1.120 - 1.160 - 1.200 - 1.240 - 1.280 - 1.320 - 1.360 Ghz
Forum: Aerial Photography and Video
01-19-2011, 03:23 PM
Replies: 4
Views: 852
Posted By kebuttke

RE: radio opinions

just in case anyone else has doubt as to my american status in a foreign country, here is my youtube channel with a few videos of the AH-64D's from my unit at their annual gunnery.
...
Forum: Aerial Photography and Video
01-19-2011, 12:15 PM
Replies: 4
Views: 852
Posted By kebuttke

RE: radio opinions

RC MANIAC119,
Then I suppose you shouldn't answer any questions from anyone regarding this type of flying as there are plenty of opportunities in the States and Europe. I feel as if...
Forum: Aerial Photography and Video
01-19-2011, 07:11 AM
Replies: 3
Views: 755
Posted By kebuttke

RE: throttle channel use mandatory?

It is a flying wing, so the throttle knob wouldn't be a big deal. I see what you are saying though. If using another channel, programming might be a little difficult. A thought about throttle...
Forum: Aerial Photography and Video
01-19-2011, 06:11 AM
Replies: 4
Views: 852
Posted By kebuttke

radio opinions

would it be worth it to buy a used 10 channel 72mhz radio with amplifier in order to be able to use 2.4ghz video transmitter with amplifier to reduce the possibility of interference? if not, what do...
Forum: Aerial Photography and Video
01-19-2011, 06:10 AM
Replies: 0
Views: 508
Posted By kebuttke

Duplicate, sorry

Duplicate. Don't know how to delete!
Forum: Aerial Photography and Video
01-19-2011, 06:01 AM
Replies: 3
Views: 755
Posted By kebuttke

throttle channel use mandatory?

ok, i have an unusual question. RC Gods, please be gentle. . . (the following DOES pertain to fpv!)

do i have to use channel 3(or whatever channel, im looking to move up in radios, still...
Forum: Unusual R/C
04-08-2008, 03:00 PM
Replies: 11
Views: 6,428
Posted By kebuttke

RE: Nitro hovercraft

maybe a small ducted fan control line motor for the air cushion and then a ducted fan for thrust. the air cushion doesnt need all that much thrust.
Forum: RC Humor
04-08-2008, 02:51 PM
Replies: 34
Views: 4,701
Posted By kebuttke

RE: Your an r/c junkie if...

and you keep losing your plane in the 150 foot cloud ceiling in 24 mph gusts.
Forum: The Clubhouse
03-05-2008, 05:55 PM
Replies: 87
Views: 7,294
Posted By kebuttke

RE: Your buddy planted his plane, what not to say?

how about when the first thing the pilot says is, "i didnt like that plane anyhow. flew like crap!"
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.