RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dtilney
Showing results 1 to 13 of 13
Search took 0.24 seconds.
Forum: Kit Building
10-12-2016, 11:24 AM
Replies: 4
Views: 1,210
Posted By dtilney

Matt - You were right. The full size plans made...

Matt - You were right. The full size plans made mention of adding a washer between the left side mounts and the firewall to give right thrust! There was no mention of this in the instructions though...
Forum: Kit Building
10-12-2016, 11:14 AM
Replies: 4
Views: 1,210
Posted By dtilney

Thanks Matt. I'll refer back to the plans to see...

Thanks Matt. I'll refer back to the plans to see if there is any angle built into the firewall. Unfortunately my firewall was supposed to have markings but it didn't have them. If it looks square...
Forum: Kit Building
10-09-2016, 09:02 PM
Replies: 125
Views: 29,815
Posted By dtilney

Thank you P-40 Driver. Should I used a sideways...

Thank you P-40 Driver. Should I used a sideways mount as the plans show, I'd need to cut away at the fuse to get the muffler to fit. But by positioning the motor rightside up, I can fit it just fine...
Forum: Kit Building
10-09-2016, 08:32 AM
Replies: 4
Views: 1,210
Posted By dtilney

Carl Goldberg Cub Motor Mount Locations?

Hi guys,

I'm building the Carl Goldberg 25th Anniversary Cub. Unfortunately the firewall I got with the kit does not have the drill hole locations for the motor mounts. Based on the plans it looks...
Forum: RCUniverse.com FAQ
10-09-2016, 08:22 AM
Replies: 4
Views: 1,192
Posted By dtilney

so how did you start it then? I can't figure it...

so how did you start it then? I can't figure it out.
Forum: Kit Building
10-09-2016, 08:12 AM
Replies: 125
Views: 29,815
Posted By dtilney

I'm building the 25th anniversary CG cub....

I'm building the 25th anniversary CG cub. Unfortunately my firewall didn't come with the motor mount drill hole locations stamped in. According to the plans, the top of the upper mount is about 3/8"...
Forum: Redcat Racing Support
02-11-2015, 07:02 AM
Replies: 8
Views: 1,797
Posted By dtilney

You're welcome. One other thing to check is to...

You're welcome. One other thing to check is to make sure nothing is binding and all wheels, axels, bearings, etc... rotate smoothly. I recently found a suspension pin had come loose and was rubbing...
Forum: Redcat Racing Support
02-10-2015, 07:08 AM
Replies: 8
Views: 1,797
Posted By dtilney

Conquest - I did more research on this and found...

Conquest - I did more research on this and found that it is not uncommon for brushless motors to behave this way over time. The term used to describe it is "cogging". I took my motor apart, cleaned...
Forum: Redcat Racing Support
01-27-2015, 08:56 AM
Replies: 8
Views: 1,797
Posted By dtilney

Hi Guys, I got the Tornado EPX back in...

Hi Guys,

I got the Tornado EPX back in August 2014. No issues what so ever, but recently I noticed it doesn't start rolling smoothly from a dead stop. It does a jerking motion for about 6 inches...
Forum: NitroModels Support
03-07-2011, 09:59 PM
Replies: 986
Views: 115,562
Posted By dtilney

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here

Need to know if the Airfield 1400mm P-40 prop will work on the Airfield 1400mm P-47.
Forum: NitroModels Support
03-07-2011, 09:44 PM
Replies: 2
Views: 1,462
Posted By dtilney

RE: Airfield 1400mm Spitfire replacement prop

Howdy ChuckW,

I have the Airfield 1400mm P-47 with the same chipped prop problem. Now that you mention it, the Spitfire and P-47 both have 13x9 props. I might just order one off the P-40 page...
Forum: NitroModels Support
01-12-2011, 06:10 PM
Replies: 7
Views: 1,936
Posted By dtilney

RE: Nitroplanes Online Support

I have used their online support many times with good success. Never had to wait long and always got good service. That is my experience.
Forum: Electric General Discussion
10-06-2009, 02:48 PM
Replies: 0
Views: 1,146
Posted By dtilney

EDF Fan Balancing

Hi Flyers,

I recently bought a new fan and housing for my foam T-45. I've read some reviews on the fan where people said they needed to balance the fan. I installed mine and it 'seems' to spin...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.