Spray bar location
12-16-2009 | 09:40 PM
#1
Thread Starter
Joined: May 2006
Posts: 454
Likes: 0
Received 0 Likes
on
0 Posts
From: Dallas
Spray bar location
This is the noob forum so I don't feel too bad asking this question: where is the spray bar in a four stroke (.91 ASP)? Is it basically where the high-speed needle enters the carb inlet?
With that question out of the way, here's why I am asking: I am installing the above engine in a Big Stik 60, and I have two ways of installing the engine. If I install the engine upright, then the spray bar (assuming the location is as I described it above) would be about 1.5" above the tank center line. If I turn the engine 90 degrees, then the spray bar would be between 1/2"-3/4" above the center line so that's probably the better set up. I just want to ensure I am measuring the location of the spray bar correctly.
Thanks.
With that question out of the way, here's why I am asking: I am installing the above engine in a Big Stik 60, and I have two ways of installing the engine. If I install the engine upright, then the spray bar (assuming the location is as I described it above) would be about 1.5" above the tank center line. If I turn the engine 90 degrees, then the spray bar would be between 1/2"-3/4" above the center line so that's probably the better set up. I just want to ensure I am measuring the location of the spray bar correctly.
Thanks.
12-17-2009 | 06:42 AM
#3
Senior Member
RE: Spray bar location
ORIGINAL: ppkk
This is the noob forum so I don't feel too bad asking this question: where is the spray bar in a four stroke (.91 ASP)? Is it basically where the high-speed needle enters the carb inlet?
With that question out of the way, here's why I am asking: I am installing the above engine in a Big Stik 60, and I have two ways of installing the engine. If I install the engine upright, then the spray bar (assuming the location is as I described it above) would be about 1.5'' above the tank center line. If I turn the engine 90 degrees, then the spray bar would be between 1/2''-3/4'' above the center line so that's probably the better set up. I just want to ensure I am measuring the location of the spray bar correctly.
Thanks.
This is the noob forum so I don't feel too bad asking this question: where is the spray bar in a four stroke (.91 ASP)? Is it basically where the high-speed needle enters the carb inlet?
With that question out of the way, here's why I am asking: I am installing the above engine in a Big Stik 60, and I have two ways of installing the engine. If I install the engine upright, then the spray bar (assuming the location is as I described it above) would be about 1.5'' above the tank center line. If I turn the engine 90 degrees, then the spray bar would be between 1/2''-3/4'' above the center line so that's probably the better set up. I just want to ensure I am measuring the location of the spray bar correctly.
Thanks.
On the ASPs I've seen, the center of the carb's rotating throttle drum is your reference point. That's actually true of all engines, even when they have a remote needle valve. Where the fuel is introduced into the intake air is the reference point.
Your idea about bhe better setup is spot on, mate.
12-19-2009 | 09:59 PM
#5
Thread Starter
Joined: May 2006
Posts: 454
Likes: 0
Received 0 Likes
on
0 Posts
From: Dallas
RE: Spray bar location
Alright, a follow-up question: what would happen if I mount the engine upright, which would put the spray bar location 1.5" above the tank center line? Would this cause the engine to run lean?
The reason I ask is, this plane is designed for the mount to be installed upright. If I turn the mount sideways, then the location of the nose gear rod would no longer line up and some modification would be needed. Nothing that is not do-able, but I'd rather avoid it if it the location of the engine doesn't cause problems in the future.
The reason I ask is, this plane is designed for the mount to be installed upright. If I turn the mount sideways, then the location of the nose gear rod would no longer line up and some modification would be needed. Nothing that is not do-able, but I'd rather avoid it if it the location of the engine doesn't cause problems in the future.
12-20-2009 | 05:19 PM
#6
Senior Member
Joined: Apr 2007
Posts: 521
Likes: 0
Received 1 Like
on
1 Post
From: Port MacquarieNew South Wales, AUSTRALIA
RE: Spray bar location
Hi ppkk,
Give it a try. Many motors will tolerate a small variation in height. If you don't achieve a reliable motor run it may well be easier to add a pump or regulator rather than re-configure the mount and nose leg steering set up.
Merry Christmas,
Colin
Give it a try. Many motors will tolerate a small variation in height. If you don't achieve a reliable motor run it may well be easier to add a pump or regulator rather than re-configure the mount and nose leg steering set up.
Merry Christmas,
Colin
