Post anything and everything lst 2 on here!
Post your Tips, ideas, specs, anything and everything ... links for hop upz even! bashing specs,vids,pics! :D Go WiLd EVEN
|
RE: Post anything and everything lst 2 on here!
1st tip... always check your electronics before cranking the engine or you might get a big suprise
|
RE: Post anything and everything lst 2 on here!
Lol ty for the post i was getting bored then (im new :(0
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: Blitz0012 :D Go WiLd EVEN |
RE: Post anything and everything lst 2 on here!
|
RE: Post anything and everything lst 2 on here!
Nice ride
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: Blitz0012 Nice ride |
RE: Post anything and everything lst 2 on here!
Yeah, props to 2d, he has tried just about everything out setup and parts wise and is always ready to share knowledge. He also puts in the time to care very well for his equipment, a lesson we could all learn from! My only question to anyone is ... has anyone made or come up with a center diff option for the lst2 yet?
|
RE: Post anything and everything lst 2 on here!
some of the usual tips that are posted everywhere on here. Dynamite engine brace, Forward only tranny conversion with gear swap, titanium turnbuckles. These are the biggest actual improvements for durability and little bit more topend. If you get alum. steering knuckles, get the ones with the little dog leg bend where the linkage attaches so you don't loose steering.(can't remember who makes them right now). If you steering is getting weak, add a few more servo saver clips, or just get the ones from ae for the mgt. that fit your servo of choice and use the bottom of them and tops from lst2 and ae clips. Gave mine better steering with hitec 5625 digital servos. Make sure fuel filter isn't pinched btween tank and engine as the vibrations can cause it to chew threw tank or header. LOCKTITE THE DRIVETRAIN SCREWS! Clean truck regularly, especially around bearings and any moving parts. Change and maintain airfilter twice the amount you think it needs, your engine will thank you. If you have the money, get many kinds of tires as different surfaces need different styles. Check, clean and maintain cvd's regularly, grit loves to eat slowly away at them causing slop and premature failure. Change wheel bearings often, at a buck apiece from avid, it is cheap insurance against a short day of running. Check wheel hex pins now and then, they break easier than you might think, and also a good time for cvd and bearing maintenance. Clean the diffs and change fluid regularly, lets you inspect them for where and broken pins inside. Will put up more if I think of them :D. Most of all, bashing or racing, HAVE FUN!!!
|
RE: Post anything and everything lst 2 on here!
1 Attachment(s)
While going over my new LST2, I've noticed the centre drive shafts seem to only just reach the centre cups (see photo). This seems odd to me, in that I think it will wear very quickly. It looks like they are 4 - 5 mm too short. Is this normal?
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: mtbkym01 While going over my new LST2, I've noticed the centre drive shafts seem to only just reach the centre cups (see photo). This seems odd to me, in that I think it will wear very quickly. It looks like they are 4 - 5 mm too short. Is this normal? |
RE: Post anything and everything lst 2 on here!
ORIGINAL: mtbkym01 While going over my new LST2, I've noticed the centre drive shafts seem to only just reach the centre cups (see photo). This seems odd to me, in that I think it will wear very quickly. It looks like they are 4 - 5 mm too short. Is this normal? |
RE: Post anything and everything lst 2 on here!
Does the LST2 come with reverse?
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: Sugafree ORIGINAL: mtbkym01 While going over my new LST2, I've noticed the centre drive shafts seem to only just reach the centre cups (see photo). This seems odd to me, in that I think it will wear very quickly. It looks like they are 4 - 5 mm too short. Is this normal? |
RE: Post anything and everything lst 2 on here!
ORIGINAL: Griffsred Does the LST2 come with reverse? |
RE: Post anything and everything lst 2 on here!
2D, what are the P/N's for the tires and wheels in the photo? I like them, they look great.
|
RE: Post anything and everything lst 2 on here!
Disregarding the hex size, does anyone know if 40 series wheel and tyres fit straight onto a LST2? I'm looking at [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_57/products_id/11541]THESE WHEELS[/link], with [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_58/products_id/3531]THESE TYRES[/link]. Thanks in advance
|
RE: Post anything and everything lst 2 on here!
I just got a lst2 for christmas but it wont do wheelies,when (santa) bought it he sad that the guy at the hobby shop sad that it will do wheelies out of the box but it dosnt I dont think it accselarte very fast to. Can you guys give me some tips on how to make it do wheelies.I also notist that the center drive shafts seemed realy colse to the end..I asome thats normal though.
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: mtbkym01 Disregarding the hex size, does anyone know if 40 series wheel and tyres fit straight onto a LST2? I'm looking at [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_57/products_id/11541]THESE WHEELS[/link], with [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_58/products_id/3531]THESE TYRES[/link]. Thanks in advance |
RE: Post anything and everything lst 2 on here!
ORIGINAL: full maxx ORIGINAL: mtbkym01 Disregarding the hex size, does anyone know if 40 series wheel and tyres fit straight onto a LST2? I'm looking at [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_57/products_id/11541]THESE WHEELS[/link], with [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_58/products_id/3531]THESE TYRES[/link]. Thanks in advance |
RE: Post anything and everything lst 2 on here!
|
RE: Post anything and everything lst 2 on here!
here are two more when the wheels and tires were just mounted and have not been driven http://i211.photobucket.com/albums/b...r/DSC03103.jpg http://i211.photobucket.com/albums/b...r/DSC03102.jpg
|
RE: Post anything and everything lst 2 on here!
That the look I'm gonna go for for bashing, looks good
|
RE: Post anything and everything lst 2 on here!
1 Attachment(s)
For 40 series wheels you need 23mm hex's but yes they work and look great as well as they preform. Here is some pics of mine
|
RE: Post anything and everything lst 2 on here!
ORIGINAL: tnnhoward 2D, what are the P/N's for the tires and wheels in the photo? I like them, they look great. Sorry just saw this. They are Mugen MBX5-T wheels and Panther Switch's. [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_57/products_id/7563]Beware these wheels are non offset... I run 9mm offset 17mm hexes....[/link] [link=http://www.amainhobbies.com/product_info.php/cPath/1_26_58/products_id/12673]Panther Switches Medium compound...[/link] |
All times are GMT -8. The time now is 03:22 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.