Carsten Products and Ultimate Jets
#1
Thread Starter
Carsten Products and Ultimate Jets
I have decided to start distributing the products designed by my friend Carsten Groen in the USA.
We have an order of a batch of Carsten's ASSI coming to Houston soon.
We will also get a batch of CAN LCD units coming, either as standalone units or as ASSI display units.
The products should be in stock at the very beginning of 2014.
Stay tuned...
We have an order of a batch of Carsten's ASSI coming to Houston soon.
We will also get a batch of CAN LCD units coming, either as standalone units or as ASSI display units.
The products should be in stock at the very beginning of 2014.
Stay tuned...
#2
Thread Starter
#5
Thread Starter
Thanks guys.
A new user manual is available on the download section of the product page.
http://www.geohei.lu/olin/data/model...al%20v0.08.pdf
The unit is now configurable as Master or Slave ( multi engine setups ) direcly in the config file that is stored on the SD card.
A new user manual is available on the download section of the product page.
http://www.geohei.lu/olin/data/model...al%20v0.08.pdf
The unit is now configurable as Master or Slave ( multi engine setups ) direcly in the config file that is stored on the SD card.
#6
Thread Starter
The units are reaching the final stage of production: i/o testing.
They will dispatch very soon!
We are starting the work on integrating these units into the Weatronic system via the serial interface. They will be Jetcat and Xycoy/ Merlin compatible initially. We are also looking at Behotec/ BF-Turbines compatibility...
They will dispatch very soon!
We are starting the work on integrating these units into the Weatronic system via the serial interface. They will be Jetcat and Xycoy/ Merlin compatible initially. We are also looking at Behotec/ BF-Turbines compatibility...
#7
Thread Starter
I have added some description on the CAN LCD product page about the ASSI and standalone versions:
http://www.ultimate-jets.net/product...lcd-can-module
http://www.ultimate-jets.net/product...lcd-can-module
#8
Attached is a piece of a log from the CANLCD module (in the standalone mode) connected to a P100RX
The following are logged every second:
1) timestamp (time since CANLCD was switched on)
2) Remaining fuel in the tank
3) RPM
4) Commanded RPM (from transmitter)
5) EGT
6) ECU battery voltage
7) Current pump voltage
8) Failsafe time (in seconds)
9) State
10) Off condition
When the CANLCD module detects that the ECU has been in failsafe for more than 30 seconds, it stop communicating with the ECU (and shows a message on the LCD screen). If not handled this way, the ECU will not (always) power down automatically when the receiver is switched off (as it will see the communication from the CANLCD and think it's services are still needed )
The following are logged every second:
1) timestamp (time since CANLCD was switched on)
2) Remaining fuel in the tank
3) RPM
4) Commanded RPM (from transmitter)
5) EGT
6) ECU battery voltage
7) Current pump voltage
8) Failsafe time (in seconds)
9) State
10) Off condition
When the CANLCD module detects that the ECU has been in failsafe for more than 30 seconds, it stop communicating with the ECU (and shows a message on the LCD screen). If not handled this way, the ECU will not (always) power down automatically when the receiver is switched off (as it will see the communication from the CANLCD and think it's services are still needed )
Last edited by Carsten Groen; 12-22-2013 at 04:19 AM.
#9
My Feedback: (4)
Join Date: Apr 2005
Location: Latrobe,
PA
Posts: 2,326
Likes: 0
Received 0 Likes
on
0 Posts
Carsten:
Very nice work !! Now you just need to make it talk to a Spektrum. FYI... over on RC Groups, there is a group of guys who have already decoded the Spektrum data buss. It's basically just I2C data.
Very nice work !! Now you just need to make it talk to a Spektrum. FYI... over on RC Groups, there is a group of guys who have already decoded the Spektrum data buss. It's basically just I2C data.
#10
Weatronic is probably closer to be available !
To be honest, maybe sometime in the future I would do something similar for other brands of transmitters (and as a personal opinion, I2C has nothing to do as an "external bus" in my opinion, it was designed to be used inside a TV and should be used as such. Many other busses are much more effective for external use, CAN, "RS232/RS485", Serial bus etc)
But as I wrote, maybe one day. The biggest part of the ASSI device was making the AoA calculations, SBUS2 telemetry and the whole autothrottle stuff (JetCat protocol was easy as I already had designed a couple of products for this)
#11
My Feedback: (76)
Join Date: Aug 2004
Location: Baton Rouge, LA
Posts: 2,715
Likes: 0
Received 0 Likes
on
0 Posts
can you make a protective plastic cover for the unit? its nice but I think it would look better with a little plastic shell like a receiver to protect the unit.
Also in the future a fuel flow meter to determine fuel usage would be really cool or perhaps this could be determined by fuel pump voltage?
Also in the future a fuel flow meter to determine fuel usage would be really cool or perhaps this could be determined by fuel pump voltage?
#12
Fuel flow, it's already there when running with JetCat and Gaspar ECU's
You will get the amount left in the tank and the amount of fuel consumed each minute (at the current power setting)
Plastic shell, that means a huge cost in tooling so this is probably a no-go. A simple solution could be a cnc milled glassfiber board that would fit below the ASSI device and fixed with 4 pcs of 2mm screws. This would make a good base for a piece of velcro etc (could also mount a plate on top of it). So far this is up to the end user.
You will get the amount left in the tank and the amount of fuel consumed each minute (at the current power setting)
Plastic shell, that means a huge cost in tooling so this is probably a no-go. A simple solution could be a cnc milled glassfiber board that would fit below the ASSI device and fixed with 4 pcs of 2mm screws. This would make a good base for a piece of velcro etc (could also mount a plate on top of it). So far this is up to the end user.
#14
Plastic shell, that means a huge cost in tooling so this is probably a no-go. A simple solution could be a cnc milled glassfiber board that would fit below the ASSI device and fixed with 4 pcs of 2mm screws. This would make a good base for a piece of velcro etc (could also mount a plate on top of it). So far this is up to the end user.
#15
Thread Starter
#16
Thread Starter
I have added a video demonstration of the CAN LCD module capability on the product page.
A must watch!
http://www.ultimate-jets.net/collect...lcd-can-module
A must watch!
http://www.ultimate-jets.net/collect...lcd-can-module
#17
Cool.May I ask what is the latency in the communication channel between actual input and reading?.will there be one for kingtech turbine?
Last edited by tornadowheel; 12-25-2013 at 11:47 PM.
#18
Thread Starter
For the ASSI unit display on the Tx, the signal travels through the air pretty much instantly to the Tx. So lag is expected to be a few ms as well.
As soon as Gaspar has finalized his serial converter, the units will be compatible with Merlin, Jet Central and Kingtech turbines. Should be very, very soon as he already has the beta prototypes running and being finalized.
I'll have the converter boards in stock as soon as they are available.
#19
Tks for your prompt reply. May I ask : what is the accuracy or tolerance limits in the readouts? Lastly will there be a protective cover over this LCD screen?
Last edited by tornadowheel; 12-26-2013 at 12:36 AM.
#20
Thread Starter
The accuracy and tolerance limits are the ones set by the ECU. Since all the information is digitally sent from the ECU to the CAN/LCD and ASSI units, there is no loss of fidelity on the display.
Typically the accuracy is set by the sensors chosen by the ECU manufacturer. EGT, RPM and pump voltage readout.
We are working on the casings for both ASSI and CAN LCD units. They will be 3D printed or basalt fiber moulded.
Last edited by olnico; 12-26-2013 at 12:39 AM.
#22
Thread Starter
With pleasure.
The price that you see on the web page is already an introduction price. As soon as the pre-order/ first batch will be passed, the price will increase.
Best regards.
The price that you see on the web page is already an introduction price. As soon as the pre-order/ first batch will be passed, the price will increase.
Best regards.
#23
Implemented the Xicoy ECU telemetry in the ASSI device today. The radio and the (optional) CANLCD module will show data from Xicoy ECUs:
1) Fuel left in tank
2) RPM
3) EGT
4) ECU battery voltage
http://www.youtube.com/watch?v=OUYSz1pjM54
1) Fuel left in tank
2) RPM
3) EGT
4) ECU battery voltage
http://www.youtube.com/watch?v=OUYSz1pjM54
#25
Thread Starter
The user manual has been updated with Xicoy setup and connection:
http://www.ultimate-jets.net/collect...en-assi-module
http://www.ultimate-jets.net/collect...en-assi-module