problems tuning jato
09-30-2005 | 11:45 PM
#1
Thread Starter
Junior Member
Joined: Sep 2005
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
From: apo,
AE
problems tuning jato
when i try to set my high idle it starts to not run at all. when i get it running again it's too rich and cuts off when i go wot. i have been messing around with the high and low idle adjustments the most, could the idle affect this problem any??? i'm in need of a little help, this is pretty frustrating.
10-01-2005 | 11:05 PM
#4
Senior Member
My Feedback: (3)
Joined: Jan 2005
Posts: 22,095
Likes: 0
Received 0 Likes
on
0 Posts
From: Macon,
GA
RE: problems tuning jato
Set the high speed needle first then the low but not till you have the HSN set correctly. If you do not adjust the low you will not get the best performance out of it. All so it can change day to day.
10-02-2005 | 02:24 AM
#5
Thread Starter
Junior Member
Joined: Sep 2005
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
From: apo,
AE
RE: problems tuning jato
yeah i know it changes with weather and other small things, plus i hear these 2.5's are real touchy to say the least. i'm plottin on gettin a new engine sometime in the future. thanx for the info.
10-02-2005 | 05:39 AM
#6
Senior Member
Joined: Nov 2004
Posts: 1,716
Likes: 0
Received 0 Likes
on
0 Posts
From: perth, AUSTRALIA
RE: problems tuning jato
i would losen the low speed like half a turn or put it back to the factory seting becuase if its ceeps on staling it sownds like it's not geting any fuel.
if this dosent work see if the fuel line is craked it might be sucking in air so theres only air going to the engein not fuel
hope this helps
if this dosent work see if the fuel line is craked it might be sucking in air so theres only air going to the engein not fuel
hope this helps
10-02-2005 | 05:46 AM
#7
Thread Starter
Junior Member
Joined: Sep 2005
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
From: apo,
AE
RE: problems tuning jato
i checked the line and its good, i believe my idle screw maybe stripped out. not completely but it doesn't stop anymore. could this be part of the problem??
10-02-2005 | 05:57 AM
#8
Senior Member
Joined: Nov 2004
Posts: 1,716
Likes: 0
Received 0 Likes
on
0 Posts
From: perth, AUSTRALIA
RE: problems tuning jato
have a look at ur carby and turn u controler on and put the brakes on if lol carby shuts then yes its striped.
if this is the case then put the trim up a bit on ur controler and see if the carby opens then dont use the brakes\
and try and start it.
and just a quetion is ur JATO new
if this is the case then put the trim up a bit on ur controler and see if the carby opens then dont use the brakes\
and try and start it.
and just a quetion is ur JATO new
10-02-2005 | 06:14 AM
#9
Thread Starter
Junior Member
Joined: Sep 2005
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
From: apo,
AE
RE: problems tuning jato
yeah, its only about six weeks old or so. and yes it does close when i hit the brakes. i already set the trim on the control to get it started w/o the brakes.
10-02-2005 | 06:20 AM
#10
Senior Member
Joined: Nov 2004
Posts: 1,716
Likes: 0
Received 0 Likes
on
0 Posts
From: perth, AUSTRALIA
RE: problems tuning jato
ok then
with the idle screw take the servo horn of off the servo(this bit that has ur brake and caby levers on)and use ur hand to hold open the carby about 1mm or so and titen the idel screw up, then after this conect it all up again and put the brakes on if the carby closes then
im sorry i cant help u any more
with the idle screw take the servo horn of off the servo(this bit that has ur brake and caby levers on)and use ur hand to hold open the carby about 1mm or so and titen the idel screw up, then after this conect it all up again and put the brakes on if the carby closes then
im sorry i cant help u any more
