The Green Pimps Build thread 56 warning
#1
Member
Thread Starter
Join Date: Oct 2006
Location: Oak Lawn, IL
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
The Green Pimps Build thread 56 warning
Here is the hole build of the Green Pimp Clod I have posted on RCC
01/28/07
02/03/07
Well today my pimp can came in the mail, Its a 17 incher. As soon as it came I immediately grabbed my clod axles and put it together. so now I mounted my battery and receiver nothing else and used green zip ties!!!
Well onto the pictures
And if you have a pimpcane you gotta post a pic of it doing this
No flex pictures though
02/06/07
Well today I took apart a knuckle to see if it had bearings in it. It does I am even happier with this truck now thats one less thing I have to buy I got a picture of the bearings
02/07/07
Made spots for the body posts today, then trimmed one of my maxx bodys and mounted it... Notice the body is maily GREEN
02/27/07
Bta steering? I think yes, I am getting a bent servo link from Moondust1950 and I will make another off of that because the steering arm link now sucks.
"thumbsup"
3/23/07
I got a couple pics today
This is my new clod with a Super rooster Ha
A while ago I talked about getting a clod in a trade for my 70 dollar mountain bike. Well I finally traded last night. I have some pictures of it to I didn't want to put this in the clod section because stock clods are junk that can't crawl, Lol. The main reason I wanted it because it came with a super rooster esc. I check today since there is no sticker on it and it is a super rooster. I drove it around last night and the crappy stock steering set up pissed me off :x So I might take it apart soon and make it a 4 linked super
Most of what it came with
Under side with the 2 good motors 2 newish speedy gems 2 motors.
The Super rooster
[IMG]http://i25.photobucket.com/albums/c53/povertyrider/IMG_0744.jpg[/IMG
03/24/07
I got my super rooster wired to deans today, and I got my moped esc wired to deans also today. I also did a little bit of re aranging the storage parts in my room for rc.
Clod buster just sitting there
Speed controller
electronics
new storage area set up
In the cabinet on the right is filled with rc wheels and tires, and spare parts, and misc rc stuff the top lifts off
my max
03/25/07
I am making up for all the pictures I didn't post for a while lol.
Truck and controller
Tq3 rear steer mod and my own neckstrap piece
With my thumb where it sits it is still confortable
Front pic showing axle servo and battery
Rear end pic showing axle, battery, wires, and servo
Body off showing the chassis with my tq3 mounted and my super rooster hooked up I just did all that about an hour ago
Esc plugged in
rx and esc plus alot of wires
Battery and crap
Chicken Butt!
rear servo
Today 04/01/07
Ordered 2 55t lathe motors, 12mm to 14mm adapters, and Thundertech adjustable motor mounts, 10t and 9t pinion.
I found some old maxx wheels and tires in my rim section of my room. I guess these will work until I can afford Axials and Xls
01/28/07
02/03/07
Well today my pimp can came in the mail, Its a 17 incher. As soon as it came I immediately grabbed my clod axles and put it together. so now I mounted my battery and receiver nothing else and used green zip ties!!!
Well onto the pictures
And if you have a pimpcane you gotta post a pic of it doing this
No flex pictures though
02/06/07
Well today I took apart a knuckle to see if it had bearings in it. It does I am even happier with this truck now thats one less thing I have to buy I got a picture of the bearings
02/07/07
Made spots for the body posts today, then trimmed one of my maxx bodys and mounted it... Notice the body is maily GREEN
02/27/07
Bta steering? I think yes, I am getting a bent servo link from Moondust1950 and I will make another off of that because the steering arm link now sucks.
"thumbsup"
3/23/07
I got a couple pics today
This is my new clod with a Super rooster Ha
A while ago I talked about getting a clod in a trade for my 70 dollar mountain bike. Well I finally traded last night. I have some pictures of it to I didn't want to put this in the clod section because stock clods are junk that can't crawl, Lol. The main reason I wanted it because it came with a super rooster esc. I check today since there is no sticker on it and it is a super rooster. I drove it around last night and the crappy stock steering set up pissed me off :x So I might take it apart soon and make it a 4 linked super
Most of what it came with
Under side with the 2 good motors 2 newish speedy gems 2 motors.
The Super rooster
[IMG]http://i25.photobucket.com/albums/c53/povertyrider/IMG_0744.jpg[/IMG
03/24/07
I got my super rooster wired to deans today, and I got my moped esc wired to deans also today. I also did a little bit of re aranging the storage parts in my room for rc.
Clod buster just sitting there
Speed controller
electronics
new storage area set up
In the cabinet on the right is filled with rc wheels and tires, and spare parts, and misc rc stuff the top lifts off
my max
03/25/07
I am making up for all the pictures I didn't post for a while lol.
Truck and controller
Tq3 rear steer mod and my own neckstrap piece
With my thumb where it sits it is still confortable
Front pic showing axle servo and battery
Rear end pic showing axle, battery, wires, and servo
Body off showing the chassis with my tq3 mounted and my super rooster hooked up I just did all that about an hour ago
Esc plugged in
rx and esc plus alot of wires
Battery and crap
Chicken Butt!
rear servo
Today 04/01/07
Ordered 2 55t lathe motors, 12mm to 14mm adapters, and Thundertech adjustable motor mounts, 10t and 9t pinion.
I found some old maxx wheels and tires in my rim section of my room. I guess these will work until I can afford Axials and Xls
#7
Member
Thread Starter
Join Date: Oct 2006
Location: Oak Lawn, IL
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
RE: The Green Pimps Build thread 56 warning
my cpe mt widener adapters came in today, I did a few runs in the house with the green body on it, and I well had made too big of body posts holes and from all the flipping over I ruined the mounting holes. So i got the tlts body on there for now.
Yes the Green pimp is Finally Pimping. Just need a steering set up to come then I can really test it :twisted:
Flex shots! "thumbsup"
^ My new background
Yes the Green pimp is Finally Pimping. Just need a steering set up to come then I can really test it :twisted:
Flex shots! "thumbsup"
^ My new background
#9
Member
Thread Starter
Join Date: Oct 2006
Location: Oak Lawn, IL
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
RE: The Green Pimps Build thread 56 warning
Thanks this thing has a million bodies!
I got bored last night and I trashed the c10 body alot of roof scratches and paint missing on it now. But today I was bored and going though the shed, and I remembered I had that extra body that came with my stock clod so i mounted that one too. lol
just a pic to get the bling bling wheels in as like the main
I think I may need to get sub cs on the knuckles eventually
I got bored last night and I trashed the c10 body alot of roof scratches and paint missing on it now. But today I was bored and going though the shed, and I remembered I had that extra body that came with my stock clod so i mounted that one too. lol
just a pic to get the bling bling wheels in as like the main
I think I may need to get sub cs on the knuckles eventually