RE: Redcat Racing Volcano Thread
 

basically you put the transmitter and car on, put the trim knobs on the transmitter to the center, try to put the throttle arm on the throttle servo so the carb is 1mm open and the brake is not on or as close as possible, put the arm on the steering servo so the wheels are as close to straight as possible then trim them the rest of the way with the trim knobs. is this what you wanted to know? there is no real set way, if you need, check out the pictures on the redcatracing.com website at the volcano to get a basic idea of how they go.

RE: Redcat Racing Volcano Thread
 

thanks ehroof
ill do it right now:D:D

RE: Redcat Racing Volcano Thread
 

maybe this will help you a little

RE: Redcat Racing Volcano Thread
 

louder you say? out it comes!

RE: Redcat Racing Volcano Thread
 

i have a volcano sv. the linkage that goes into the gear box broke. i can pull the rod completely out. the engine starts and when you squeeze the throttle it revs but the wheels dont turn. i need some suggestions on what to do.

RE: Redcat Racing Volcano Thread
 

what do yall think of the electric starter?
my pull is broken and electric is $7 more
http://cgi.ebay.com/Power-Starter-fo...QQcmdZViewItem

RE: Redcat Racing Volcano Thread
 

do you mean the brake linkage? if so, there is a small grub screw that hold it in place, right on top inside the chrome piece above it. check the grub screws in the drive cups (cups that hold the dogbones). also make sure the slipper clutch is tight on the trans, its the nut behind the spur gear.

RE: Redcat Racing Volcano Thread
 

seems like a good deal, i dont like rotostarts, you need that charged battery all the time, not saying its not good, i used to love it on my hpi till i showed up to the track with a dead battery, within a 1/2 hour i had a pull start on it and a starter box.

RE: Redcat Racing Volcano Thread
 

its the chrome piece that goes into were all the gears are that is also attach to the throttle the chrome rod now can be pulled aot easly so do i need to take all that apart and if so is there an easyer way then taking the whole car apart?

RE: Redcat Racing Volcano Thread
 

thats the brake rod, there is a pad behind the brake that the flat part of that rod sits one. should stay in place if installed right.

RE: Redcat Racing Volcano Thread
 

i had my first run in the snow and first fun in 6 monthes!
any suggestions of after run in the snow
i just take the upper plate off and take all the snow off that i can and put it next to the furnace
any ofther tips to prevent anything bad?

RE: Redcat Racing Volcano Thread
 

god ehroof i was just looking through your gallery
what do you do for work to have that many R/Cs????!!!!
I was like.... [sm=omg_smile.gif][sm=greedy.gif][sm=greedy.gif]

RE: Redcat Racing Volcano Thread
 

spray the whole rc down with wd40 before you run it and after when its dry, blow off the excess if you have a compressor or can of air.

RE: Redcat Racing Volcano Thread
 

lol and thats not all of them. I am a GC in NYC and the 5 boro's but i am looking for something else to do soon, dont know what yet. lol

RE: Redcat Racing Volcano Thread
 

I can move my spur gear left and right, there is a space of about an 1/8" between the nut and the side of the case. I assume the spur gear shouldn't slide side to side. I tried to loosen the nut with a wrench but couldn't hold the spur gear. What is the easiest way to adjust this? Do i have to remove the transmission?

Thanks

RE: Redcat Racing Volcano Thread
 

you need to tighten it, not loosen it then, just hold the gear with one finger and use a wrench and tighten the slipper nut.

RE: Redcat Racing Volcano Thread
 

does any 1 have an electric starter for volcano?

RE: Redcat Racing Volcano Thread
 

do you mean the wand or the backplate and do you mean for you to buy?

RE: Redcat Racing Volcano Thread
 

I just wanted to know if any 1 had any experence with the same system

whats a GC?

and how did you stumble upon my video?
http://www.youtube.com/watch?v=Khmm2aOQRc8

RE: Redcat Racing Volcano Thread
 

http://www.redcatracing.com/itemdeta...p?partno=08018
http://www.redcatracing.com/itemdeta...p?partno=08022
will these replace my front and rear drive shaft and drive cups?
Parts below
http://www.redcatracing.com/itemdeta...p?partno=02016
http://www.redcatracing.com/itemdeta...p?partno=08061
http://www.redcatracing.com/itemdeta...p?partno=08060

because one fell off today and i couldnt find it!

RE: Redcat Racing Volcano Thread
 

i had the rotostart on my hpi's and took it off once i had no charged battery and couldnt race [:o]

GC=General Contractor

RE: Redcat Racing Volcano Thread
 

thats the brake rod, there is a pad behind the brake that the flat part of that rod sits one. should stay in place if installed right.


it does stay in place but i tore the gasket and dont know where to get one any ideas?

RE: Redcat Racing Volcano Thread
 

what gasket?

RE: Redcat Racing Volcano Thread
 

PLEASE help?

RE: Redcat Racing Volcano Thread
 

ok

the 2 shafts on the top are for the transmission, the gears go on them

02016 are for the front and rear diff,
02003 goes from the trans to the rear diff
06006 goes from the trans to the front diff