Canadian Kit Cutters
03-28-2002, 10:52 PM
#1
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Jan 2002
Location: Kitchener,
ON, CANADA
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Canadian Kit Cutters
Can anyone tell me if there are any Canadian kit cutters, and if so who are they and where are they located.
Thanks for the help,
Steve
Thanks for the help,
Steve
04-08-2002, 11:39 PM
#3
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Jan 2002
Location: Kitchener,
ON, CANADA
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Hmmm, how to answer this without being insulting....
If I could tell you who the Canadian kit cutters were, WHY would I post this subject?? I guess since I'm Canadian I should know what every r/c company is in my country....I smell a Molson Canadian commercial coming on.....
Steve
04-09-2002, 01:23 AM
#4
Member
My Feedback: (1)
Join Date: Feb 2002
Location: Ajax,
ON, CANADA
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Canadian Kit Cutters
Trillium Balsa in Tillsonburg can laser cut kits. I don't know if they will cut a kit from any plans or if they only work with kit manufacturers but it doesn't hurt to send them an email to find out. I believe Kitchener is not too far from Tillsonburg?
Check out the site at:
Trillium Balsa
As for the Molson Canadian comercials...I personally love the one where the American guys in the bar ask the Canadian guy where is his pet beaver....what a hoot!
Check out the site at:
Trillium Balsa
As for the Molson Canadian comercials...I personally love the one where the American guys in the bar ask the Canadian guy where is his pet beaver....what a hoot!
04-09-2002, 02:18 AM
#5
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Jan 2002
Location: Kitchener,
ON, CANADA
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Thank you Derrick
That's exactly what I was looking for Derrick, and you're right, Tillsonburg isn't that far from Kitchener!The actual Molson commercial I was thinking of when I made that post was the one where the girl asks the guy if he knows Glen, the Canadian, who works in an office and says "eh" alot. Only to have the Canadian guy turn around and say "Oh yeah, Glen the office guy..... he's dead." I was howling when I saw that one!
Thanks again,
Steve
04-12-2002, 12:15 PM
#10
Senior Member
Join Date: Dec 2001
Location: Brantford, ON, CANADA
Posts: 3,305
Likes: 0
Received 0 Likes
on
0 Posts
Trouble
I know I am going to regret this, I just know it.
If you really must know. On another Forum I gave some advice on how to break in an engine, (I do have knowledge on this subject). Then every engine "Expert" that did not know how to run an engine jumped on the bandwagon. Even started calling me names!!
Ed S
If you really must know. On another Forum I gave some advice on how to break in an engine, (I do have knowledge on this subject). Then every engine "Expert" that did not know how to run an engine jumped on the bandwagon. Even started calling me names!!
Ed S
04-13-2002, 02:52 AM
#12
My Feedback: (60)
Join Date: Dec 2001
Location: Litchfield Park,
AZ
Posts: 7,677
Likes: 0
Received 25 Likes
on
23 Posts
Canadian Kit Cutters
Shortman, I think you're thinking of box cutters. At least I hope you just misunderestood the question. What Steve needs is somebody who cuts airplane kits from plans. Thanks, Chad.
