RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Hesp
Showing results 1 to 11 of 11
Search took 0.04 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-08-2018, 03:46 PM
Replies: 2
Views: 786
Posted By Hesp

Thanks so much for your reply. The short switch...

Thanks so much for your reply. The short switch sounds like the way to go.I'm sure if I had had a short switch to begin with it would not have snagged & bent. When I went to straighten it out it...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-08-2018, 10:33 AM
Replies: 2
Views: 786
Posted By Hesp

Airtronics SD-6G trans toggle switch

The retract toggle switch on my Airtronics trans needs replacing. As Airtronics is mostly out of business I need a source for the retract toggle switch. Any help would be most appreciated .
Forum: Electric General Discussion
04-07-2018, 01:10 PM
Replies: 10
Views: 1,942
Posted By Hesp

Batteries are dangerous. Recently heard of an...

Batteries are dangerous. Recently heard of an electric car ( full size ) that crashed & the battery burst into flames. Took 5 fire engines & 35 fire fighters to put it out. They would put it out &...
Forum: Electric General Discussion
04-07-2018, 12:38 PM
Replies: 0
Views: 459
Posted By Hesp

Turnigy G-46 550kv-670kv ?

Does any one have experience with the Turnigy G-46 motor in 550 or 670 KV . I have a supply of APC 14/10 props I would like to use on this motor. on a plane I estimate will be under 5 lbs. all up...
Forum: Airtronics Support Forum
03-07-2016, 01:22 PM
Replies: 10
Views: 1,693
Posted By Hesp

Well guys problem solved. After talking to the...

Well guys problem solved. After talking to the Airtronics tech line here is what I found. I had both servo arms pointing in the same direction to the right. The help tech said each servo arm needed...
Forum: Airtronics Support Forum
03-07-2016, 11:58 AM
Replies: 10
Views: 1,693
Posted By Hesp

Hey Todd thanks for the reply. I did select the...

Hey Todd thanks for the reply. I did select the "Delta Wing" aero type first, then proceeded forward. It's the forward part that I am having trouble with. This is my first computer radio ( Airtronics...
Forum: Airtronics Support Forum
03-07-2016, 11:51 AM
Replies: 10
Views: 1,693
Posted By Hesp

Your reply is most appreciated. The first thing I...

Your reply is most appreciated. The first thing I did was to select "Delta Wing" as the aero type. I'm sure there is some small detail I'm missing. I see that Airtronics list an !-800-262-1178 help...
Forum: Electric Aerobatic & Sport Planes
03-07-2016, 07:08 AM
Replies: 7
Views: 1,911
Posted By Hesp

40 size electric motor

Good day again sir. I live & fly on my land at 7700' elevation in Colorado. The air here is much thinner than at closer to sea level. This thin air requires a different learning curve in order to...
Forum: Electric Aerobatic & Sport Planes
03-06-2016, 04:02 PM
Replies: 7
Views: 1,911
Posted By Hesp

Good day sir. As an old flyer myself I have...

Good day sir. As an old flyer myself I have switched to all electric power. I am not familiar with the pulse 15 or 40 you mentioned but there are many 40 size models to choose from. As for a 40-46...
Forum: Airtronics Support Forum
03-06-2016, 02:26 PM
Replies: 10
Views: 1,693
Posted By Hesp

Thanks for the reply. My radio must be different...

Thanks for the reply. My radio must be different than yours. There is no "Tail>2xEL" on my navigation system that I can find.. Where I'm at right now is I have a mix in. Problem is that ail. is on...
Forum: Airtronics Support Forum
03-06-2016, 09:16 AM
Replies: 10
Views: 1,693
Posted By Hesp

Airtronics Delta wing mixing

This is my first post. I am 71 years old & have been building & flying model airplanes from about 1958. My question is: I have an Airtronics SD-6G radio. I have been able to follow the owners manual...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.