RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: hkilian
Showing results 1 to 14 of 14
Search took 0.60 seconds.
Forum: OMP - Ohio Model Products Support Forum
06-28-2009, 05:58 PM
Replies: 17
Views: 2,815
Posted By hkilian

RE: OMP Yak 65

Brian,

A couple on installation comments on the YS 1.10.
Be very careful with the installation into the provided wood rails. In my case they were not well glued into the structure and were...
Forum: OMP - Ohio Model Products Support Forum
06-15-2009, 05:13 PM
Replies: 14
Views: 2,155
Posted By hkilian

RE: Saito stack so close to the fuse.....

I'm not Mike but the clearance should be plenty to keep your plane from coming down in flames. Have to use my infrared thermometer on my YS 1.10 exhaust but I doubt very much I'll see temps that...
Forum: OMP - Ohio Model Products Support Forum
05-10-2009, 09:34 AM
Replies: 3
Views: 1,370
Posted By hkilian

Tetherite Landing Gear

The attached photo shows my Yak 65 sitting on the medium size gear that I bought after having to bend the original Aluminum gear back into shape too often. The plane weighs a smidgen over 8 pounds...
Forum: OMP - Ohio Model Products Support Forum
10-23-2008, 04:58 PM
Replies: 6
Views: 840
Posted By hkilian

RE: thrust plates

And I thought I was cheap...
Herb
Forum: OMP - Ohio Model Products Support Forum
10-20-2008, 03:44 PM
Replies: 11
Views: 1,390
Posted By hkilian

RE: 65"YAK-SP65M kit??

Mike,

As you are improving the kit, please make sure to pay attention to the motor mount. As I have already stated in this forum, the two hardwood beams on the older ARF are set into a "sea of...
Forum: OMP - Ohio Model Products Support Forum
06-15-2008, 11:14 AM
Replies: 10
Views: 1,369
Posted By hkilian

RE: Rudder Flutter Yak 65"

I made the changes we discussed and no more flutter was observed. A no-play reasonably strong servo on the rudder (>80 ozin) with direct coupling will do, I believe. The many comments on speed...
Forum: OMP - Ohio Model Products Support Forum
06-05-2008, 08:37 AM
Replies: 10
Views: 1,369
Posted By hkilian

RE: Rudder Flutter Yak 65"

Spacey,

My prop is an APC 15x10 and the control surfaces are all sealed with tape. Not sure if I always fully close the throttle when pointing downhill but the flutter has also been observed in...
Forum: OMP - Ohio Model Products Support Forum
06-04-2008, 04:24 PM
Replies: 10
Views: 1,369
Posted By hkilian

Rudder Flutter Yak 65"

After now over 15 flights on my still new Yak 55 (65") with a YS 1.10 I have couple of questions:

Although I try to avoid flying this plane fast (as is suggested in the manual), the rudder has a...
Forum: OMP - Ohio Model Products Support Forum
05-08-2008, 05:37 PM
Replies: 7
Views: 1,119
Posted By hkilian

RE: Pics of my new yak 55 SP

Well, here is my ARF YAK 55 in flight. Bought it as a combo with the YS 1.10 at the Toledo Show last month. After breaking in the engine and enforcing the motor mount area I'm completely happy...
Forum: OMP - Ohio Model Products Support Forum
04-29-2008, 08:02 AM
Replies: 12
Views: 1,627
Posted By hkilian

RE: Vibration and 4 strokes

Aviti,
I have the same model/motor combination that you mention - OMP Yak 65 and YS 110. The motor shook so badly, it broke and loosened the mounting rails and the structure they are glued to...
Forum: Profile and Fun Flying Planes
04-28-2008, 10:20 AM
Replies: 19
Views: 3,099
Posted By hkilian

OMP Yak 65, YS 110 Combo

At the Toledo show this April I bought the OMP Yak 65 ARF with a YS 1.10 engine. Plane went together very well and was completed without problems. I'm using Hitec 645 servos for control surfaces...
Forum: Kit Building
01-01-2007, 11:31 AM
Replies: 6
Views: 1,032
Posted By hkilian

RE: RV-4 wing rebuild

I built the RV4 some time ago and was not happy with the way the the first wing came out. I re-ordered a complete new wing and received all necessary materials prompty. The second time around it...
Forum: Kit Building
12-26-2006, 05:37 PM
Replies: 3
Views: 980
Posted By hkilian

Building board for small Dumas airplane

After building kit planes for a number of years on all kind of boards and always cursing the fact that push pins don't really want to stay put, I am tackling now a Dumas Waco YMF 5. The kit is...
Forum: RC Gliders, Sailplanes and Slope Soaring
07-24-2004, 06:24 PM
Replies: 0
Views: 1,187
Posted By hkilian

Graupner LS8 Glider, anyone with experience?

Since I fly a full scale Rolladen Schneider LS8-18 and also do some RC flying, my son thought it would be a neat idea to give me a model of my glider as a present. He found a kit for this...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.