RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: higgy1541
Showing results 1 to 25 of 79
Search took 0.82 seconds.
Forum: 3D Electric Flying!
03-05-2008, 10:06 AM
Replies: 7
Views: 4,913
Posted By higgy1541

RE: Seagull Edge 540 60 e-conversion

I have this Seagull Edge with an electric setup. This is the motor I used; Link I am using this with an OMERC 100A ESC and Polyquest 8S 4350 packs. I am currently using an APC-E 18x10 prop and it is...
Forum: 3D Electric Flying!
02-25-2008, 04:50 PM
Replies: 4
Views: 898
Posted By higgy1541

RE: Increasing the number of cells?

The AUW is 8.5 lbs which equates to about 200w per lb. The batteries used are Polyquest 4350mah 4S wired in series to give 8S. I am using an 18x10 prop with that motor and is currently drawing 65A,...
Forum: 3D Electric Flying!
02-19-2008, 01:55 PM
Replies: 4
Views: 898
Posted By higgy1541

Increasing the number of cells?

I have just finished building a 68" Edge 540 with an electric setup. I have this motor; Link , 100A Omerc ESC, 4350 8S Polyquest Li-po's and an APC 18x10 prop. Its currently pulling 65A and 1800W. My...
Forum: ARF or RTF
01-30-2008, 11:58 AM
Replies: 939
Views: 154,271
Posted By higgy1541

RE: Seagull Edge 540 - 68" (60-90) ARF New v2- Building

Am just putting one of these together with an electric setup. I just have a quick question. How important are the supporting struts on the tail? Has anyone not used them in the build?

Here are...
Forum: Giant Scale Aircraft - General
06-22-2007, 05:08 PM
Replies: 2
Views: 655
Posted By higgy1541

RE: extremeflight74"yak

I am currently building one of these with a Brillelli 46GT Gas engine see www.brillelli.com

There is quite a bit of information on this website and www.***********.com on this plane if you...
Forum: RC Pattern Flying
02-26-2007, 03:14 PM
Replies: 529
Views: 166,268
Posted By higgy1541

RE: New Kyosho Oxalys 50 ?

I am 100% sure the Oxalys is going to be my next pattern plane. I am now just debating whether to put a YS-63 or a Saito 82 in it. Does anyone have any pros/cons of either engine with this plane? Any...
Forum: Glow Engines
01-25-2007, 01:24 AM
Replies: 19
Views: 3,420
Posted By higgy1541

RE: Saito 65 tuning

I have a slighly older Saito .65, says version 2000 on the front of my manual. Whereas the newer manuals say 2.5 turns out on the high speed needle initialy the older one says FIVE turns out! Is...
Forum: Glow Engines
01-24-2007, 04:01 PM
Replies: 5
Views: 725
Posted By higgy1541

RE: Idle on Saito 65

Thanks for the input. Just so I know, what would be a good idle speed for this engine?
Forum: Glow Engines
01-24-2007, 06:33 AM
Replies: 5
Views: 725
Posted By higgy1541

Idle on Saito 65

I have just bought a used Saito 65 off a friend. It seems to run very reliably except there is quite a bit of vibration at idle. This is my first four stroke so am not sure how much vibration there...
Forum: 3D Flying!
01-15-2007, 11:17 AM
Replies: 0
Views: 423
Posted By higgy1541

What Prop on Saito .65 in an Extra 300S

I have got a 58" Span Blackhorse Extra that I am going to put a Saito .65 into. I just wonderd if anyone has experience of this engine in an aerobatic model and what props you would recomend.

...
Forum: Beginners
10-03-2006, 12:39 PM
Replies: 3
Views: 706
Posted By higgy1541

RE: Which Li-Po in GWS Formasa

I decided on and bought the 1200. Just that bit more capacity and about the same weight as the standard nimh it came with.
Forum: T-Rex heli
10-03-2006, 11:25 AM
Replies: 8
Views: 938
Posted By higgy1541

RE: Is the Futaba 6EXH adequate for the Rex 450XL?

I use a 6EXH with my Walkera 36 and T-Rex 450SE. No complaints at all, its a great budget radio.
Forum: Beginners
10-02-2006, 02:54 PM
Replies: 3
Views: 706
Posted By higgy1541

Which Li-Po in GWS Formasa

I have just gone brushless in my GWS Formosa.The brushless motor is a 400 equivilent and is pulling 10-14amps. I am looking at getting a couple of li-pos. The ones I am going for are Flightpower, one...
Forum: T-Rex heli
09-30-2006, 03:01 AM
Replies: 5
Views: 756
Posted By higgy1541

RE: My New T-Rex 450SE

Yes IF I ever get bored with it, its yours.
Forum: T-Rex heli
09-29-2006, 11:18 AM
Replies: 5
Views: 756
Posted By higgy1541

My New T-Rex 450SE

Almost finished my 450SE. This is what it has:

Futaba R146iP PCM Recevier
3 x HS-65HB Servos
GY401 + HS-577 Digital Servo
Align 430L Motor + Align 35G ESC
Flightpower 1800 3S1P Li-Po
...
Forum: Walkera Helis - Dragonfly, etc..
09-07-2006, 07:05 AM
Replies: 0
Views: 354
Posted By higgy1541

How many amps?

I am currently using an Align 430L motor(the one with the silver ends) and ALign 35A ESC. My Li-po is a Flightpower 1800mah 3S1P 20C. During hovering and basic forward flight, how many amps would you...
Forum: Walkera Helis - Dragonfly, etc..
09-02-2006, 12:24 AM
Replies: 10
Views: 1,184
Posted By higgy1541

RE: Wooden Blades for 36

So the blades have no covering, they are just the bare wood?
Forum: Walkera Helis - Dragonfly, etc..
09-01-2006, 04:44 PM
Replies: 10
Views: 1,184
Posted By higgy1541

RE: Wooden Blades for 36

I was thinking about just giving the blades with the stripped off covering a coat of clear lacquer.
Forum: Walkera Helis - Dragonfly, etc..
09-01-2006, 02:47 PM
Replies: 10
Views: 1,184
Posted By higgy1541

RE: Wooden Blades for 36

ummmm, little bit late. I took the covering off one set. Does anyone else have experience with these blades?
Forum: Walkera Helis - Dragonfly, etc..
09-01-2006, 09:57 AM
Replies: 10
Views: 1,184
Posted By higgy1541

RE: Wooden Blades for 36

Ok thanks, Just didnt want to go ripping it all off to find out i ruined a set of blades.
Forum: Walkera Helis - Dragonfly, etc..
09-01-2006, 09:45 AM
Replies: 10
Views: 1,184
Posted By higgy1541

Wooden Blades for 36

I have just purchased some wooden blades for my 36. I got them from HeliDirect, you can see the blades here . I have just recieved them and they have got a white plastic covering on them. Does the...
Forum: Walkera Helis - Dragonfly, etc..
08-26-2006, 03:56 AM
Replies: 10
Views: 960
Posted By higgy1541

RE: Finished Upgrading my 36

Yes the HS-56 servos are a direct replacement. The only you have to do is trim the tabs off the side and also the HS-56's have two holes for mounting so you need to drill a hole in the centre for the...
Forum: Walkera Helis - Dragonfly, etc..
08-24-2006, 05:18 PM
Replies: 10
Views: 960
Posted By higgy1541

RE: Finished Upgrading my 36

I am also in the learning stage. Havent tried it out yet, as long as the weather holds out it will have its first flight, since upgrading it, tommorow. I have spent about £300 upgrading it, not sure...
Forum: Walkera Helis - Dragonfly, etc..
08-24-2006, 02:57 PM
Replies: 10
Views: 960
Posted By higgy1541

Finished Upgrading my 36

I have just finished upgrading my walkera 36. As a learner I was getting tired of the unreliable standard electrics. Here is what I have got for it:

Futaba 6EXH Tx
Futaba R146iP PCM Receiver
...
Forum: Walkera Helis - Dragonfly, etc..
08-20-2006, 04:05 AM
Replies: 12,090
Views: 979,428
Posted By higgy1541

RE: Walkera Dragonfly #36

How many teeth is the main gear on the 36?
Showing results 1 to 25 of 79
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.