RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: akashowtime
Showing results 1 to 10 of 10
Search took 0.34 seconds.
Forum: Giant Scale Aircraft - General
02-05-2009, 07:15 PM
Replies: 2
Views: 743
Posted By akashowtime

RE: *** DC-3 fiber clasic MANUAL wanted ***

COULD YOU TELL ME WHERE Y OU GOT YOUR DC3? IN USA OR OUT OF STATES AND WAS THE PRICE OUT RAGEST OR NOT TO BAD THANKS FOR ANY INFORMATION.
Forum: Twin & Multi Engine RC Aircraft
11-09-2008, 05:15 PM
Replies: 198
Views: 41,917
Posted By akashowtime

RE: Nosen Cessna 310

Hay Sam

I'am geeting info on the retracks, and if it works out I will work something out with you. I have a dealer checking with robart to see if I can even get them.
Forum: Twin & Multi Engine RC Aircraft
11-08-2008, 12:27 PM
Replies: 198
Views: 41,917
Posted By akashowtime

RE: Nosen Cessna 310

Hi new to thread.

Just got my nib bn origanl 310. and have parts orderd from g&l hobbies. Any one use centruy jet retracks?
Read most of thread and where can I find prints, I have the ones...
Forum: 3D Flying!
09-04-2008, 09:21 PM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

I think the os 200 should be ok. I'am running a satio 220 and can hover just under 1/2 thro-.
and it is not bad on fuel.
Forum: 3D Flying!
06-22-2008, 04:01 PM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

Today was the first flight of my H-260. Plane is awsome the way it handled, just needed Two clicks up trim and was good from there out. Saito 220 has tuns of power, hover at 1/2 speed.
tonly...
Forum: 3D Flying!
03-31-2008, 07:55 PM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

Hi Bob

They will replace the fuse. I plan on gluing the stab together, lucky I had not done it yet. I did just get done gluing the hole front end with epoxy. Better to waste two hrs than to...
Forum: 3D Flying!
03-31-2008, 07:01 PM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

Thanks for the good information on the servos. Another possable problem, I slid in the wing tube and the elevater tube and looking from the back of the rudder they are not runing peralel. Theres...
Forum: 3D Flying!
03-30-2008, 07:05 AM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

Started putting together my HR 260 today. Have all hitec 645 servos for her anyone see any problems with those. Also have a sat-220 for power.
Forum: 3D Flying!
03-26-2008, 06:32 PM
Replies: 3,636
Views: 426,074
Posted By akashowtime

RE: Extra 260 27% Hangar 9er

I was reading through all pages being that I'am about to put together my H9 260 and in one I noticed someone said that the futaba 7c did not have ability to run two servos on the elevaters.
Thats...
Forum: Gas Engines
01-22-2008, 07:59 PM
Replies: 25
Views: 5,945
Posted By akashowtime

RE: Hangar 9 Extra 260 Engine Selection

I just orderd my 260 and have a satio 220 for it, please someone tell me this is a good pick.

I want to hover and need power to pull out of it.
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.