RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: big_ipaq
Showing results 1 to 18 of 18
Search took 0.31 seconds.
Forum: Futaba Radios Direct support forum
06-03-2009, 01:23 PM
Replies: 1
Views: 480
Posted By big_ipaq

RE: 7CAP Fasst - Throttle cut

OK. Found the answer myself...<div>
</div><div>http://www.futaba-rc.com/faq/faq-7c-q743.html</div><div>
</div><div>
</div>
Forum: Futaba Radios Direct support forum
06-03-2009, 12:29 PM
Replies: 1
Views: 480
Posted By big_ipaq

7CAP Fasst - Throttle cut

I never understood how to set up throttle cut with my 7CAP. On my 14MZlooks much more clear even though, I've encountered myself some problems there too.

Now, I want to setup my 7CAP for a nitro...
Forum: Futaba Radios Direct support forum
05-22-2009, 02:45 AM
Replies: 8
Views: 1,383
Posted By big_ipaq

RE: Trainer 14MZ / Student FF9-super: channels different, can this be solved?

This would be a very nice function to have. I assume that we still do not have any news from Futaba after 3 years...<div>
</div><div>
</div>
Forum: Futaba Radios Direct support forum
05-04-2009, 10:12 AM
Replies: 7
Views: 1,883
Posted By big_ipaq

RE: Why has the Futaba R6014 been discontunued?

OK, can you please address this new technology and its implications?
Forum: Futaba Radios Direct support forum
05-03-2009, 05:55 PM
Replies: 7
Views: 1,883
Posted By big_ipaq

RE: Why has the Futaba R6014 been discontunued?

Second question was answered, but the first one was not. So again, why was discontinued? Any problems with it? What are the differences between the old one and the new one?
Forum: Futaba Radios Direct support forum
01-28-2009, 03:19 AM
Replies: 1
Views: 642
Posted By big_ipaq

14MZ switch channel assignment

Hi, I want to program on SW-D channel 7 with the following positions: 0 - 0%, 1 - 50%, 2 - 100%. I do not want to use End Point - ATV to limit to 0%.
Forum: Futaba Radios Direct support forum
01-20-2009, 02:46 PM
Replies: 4
Views: 739
Posted By big_ipaq

RE: End Point question

I have the exact same question for 14MZ. Also which one you adjust first, expo, D/R, ATV? Does the order matter?
Forum: Futaba Radios Direct support forum
01-11-2009, 11:18 AM
Replies: 4
Views: 626
Posted By big_ipaq

RE: 6014 - weak servi pulse?

How lower voltage will increase operational speed? Speed of servo? What else should I be afraid of?
Forum: Futaba Radios Direct support forum
01-09-2009, 09:28 PM
Replies: 4
Views: 626
Posted By big_ipaq

6014 - weak servi pulse?

I found the following product: SERVO-PULSE-BOOSTER (AMPLIFIER) from a company whose products I am often using. All was well until I wanted to check what is this product, and in product desciption I...
Forum: Futaba Radios Direct support forum
01-06-2009, 11:09 AM
Replies: 1
Views: 641
Posted By big_ipaq

RE: 14mz Transmitter case

My problem exactly. I only have my 14MZ since September and already the padding is tearing apart...
Forum: Futaba Radios Direct support forum
10-11-2008, 04:01 PM
Replies: 4
Views: 749
Posted By big_ipaq

RE: 14MZ 2.4 file additions ?

No, the plug on the side is a USB plug, exclusively at this time for factory use. You won't find drivers for it and you cannot use it. Take the card out and use a standard card reader with your...
Forum: Futaba Radios Direct support forum
10-10-2008, 04:16 PM
Replies: 3
Views: 1,161
Posted By big_ipaq

RE: TM-14 ANTENNA

Nevertheless, Futaba in the TM-14 instruction manual is saying clearly to point it UPWARDS not DOWNWARDS. And the pictures in the booklet show it also pointing UPWARDS. Is there any possibility to...
Forum: Futaba Radios Direct support forum
10-05-2008, 04:37 AM
Replies: 7
Views: 1,221
Posted By big_ipaq

RE: Is 5cell(6V) ok with FASST 6/7/8/14 RX?

Yes, true, but then, why Futaba does not recommend using 5 cell?
Forum: RC Gliders, Sailplanes and Slope Soaring
08-02-2008, 03:26 PM
Replies: 2
Views: 644
Posted By big_ipaq

RE: Battery overheats and RC motor stop working

Probably the battery discharge rate is not enough for the amperage required by your motor/propeller setup. You have nothing to check, maybe except a shop selling better batteries. Or you should check...
Forum: RC Gliders, Sailplanes and Slope Soaring
07-29-2008, 01:00 PM
Replies: 3
Views: 4,062
Posted By big_ipaq

RE: Graupner Maxie Sport 3200mm motorglider

No, actually not even flaps. One servo for each aileron on each wing. One for the elevator and one for the rudder. 4 in total. Remember this is not an aerobatic motorglider, and the wing is...
Forum: RC Gliders, Sailplanes and Slope Soaring
07-29-2008, 08:08 AM
Replies: 3
Views: 4,062
Posted By big_ipaq

RE: Graupner Maxie Sport 3200mm motorglider

Here are the pictures of the kit as I received it.
Forum: RC Gliders, Sailplanes and Slope Soaring
07-29-2008, 08:02 AM
Replies: 3
Views: 4,062
Posted By big_ipaq

Graupner Maxie Sport 3200mm motorglider

I've bought a while ago a Graupner Maxie Sport motor glider. I will post here posts with my build log and every other detail I have. For now, the link to the producer's website page.

...
Forum: RC Gliders, Sailplanes and Slope Soaring
06-14-2008, 04:25 PM
Replies: 6
Views: 1,445
Posted By big_ipaq

Advanced Sailplane

I am looking for a large sailplane with kit with spoiler and flaps for advanced pilots, designed for thermaling. Any recomandations?
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.