RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: steveukflyer
Showing results 1 to 17 of 17
Search took 0.61 seconds.
Forum: MVVS Support
09-05-2006, 01:22 PM
Replies: 1
Views: 636
Posted By steveukflyer

RE: 91 exhaust timing

What no one running a pipe on this engine[X(]

I suppose I'll have to get my protractor out:eek:

Steve
Forum: Glow Engines
09-01-2006, 04:48 PM
Replies: 13
Views: 1,525
Posted By steveukflyer

RE: Need a hot 15-25

Enya ss15bb will hover a near 4lb plane

http://www.servoshop.co.uk/index.php?pid=LSS15BBTN&area=Engines

might be worth a look

Steve
Forum: MVVS Support
09-01-2006, 03:32 PM
Replies: 1
Views: 636
Posted By steveukflyer

91 exhaust timing

Hi

Can you tell me the exhaust timing period for the mvvs 91 please?

I have a range of different pipes to choose from and need to work out a starting point for the manifold, many thanks
...
Forum: RC Pattern Flying
11-17-2005, 03:29 PM
Replies: 9
Views: 1,943
Posted By steveukflyer

RE: Pattern planes and full span ailerons.

HI Snap

From what I've gathered over the years it used to be thought that putting the stab higher meant that the tail-plane would be more efficient if it wasn't in the wake of the wing. However...
Forum: Glow Engines
11-04-2005, 01:10 PM
Replies: 35
Views: 7,681
Posted By steveukflyer

RE: Enya 53-4c Knocking

Thank goodness for that - well done[8D]

Steve
Forum: Glow Engines
11-03-2005, 05:37 AM
Replies: 35
Views: 7,681
Posted By steveukflyer

RE: Enya 53-4c Knocking

Ed

Looks like we'll have to put this one down to language differences[sm=wink.gif]

Regards

Steve
Forum: Glow Engines
11-02-2005, 09:34 AM
Replies: 35
Views: 7,681
Posted By steveukflyer

RE: Enya 53-4c Knocking

Ed

It's because the engine has a mechanically 'fixed' timing that the ignition timing is varied by the fuel, which is why you may have to richen the fuel mixture when using a larger prop. A...
Forum: Glow Engines
11-02-2005, 07:50 AM
Replies: 35
Views: 7,681
Posted By steveukflyer

RE: Enya 53-4c Knocking

Dar

No problem, the exchange of ideas and knowledge is what it's all about[8D], BUT as was mentioned in one of the posts :

>>The reason I brought this up, is I don't want inexperienced...
Forum: Glow Engines
11-02-2005, 05:49 AM
Replies: 35
Views: 7,681
Posted By steveukflyer

RE: Enya 53-4c Knocking

Hi Chaps

There seems to be an awful lot of "experts" on this thread, just like at my club field :eek:

It is perfectly clear that Dar does actually know what he is talking about in this...
Forum: Glow Engines
06-08-2005, 10:46 AM
Replies: 11
Views: 4,601
Posted By steveukflyer

RE: RC Engine Bearings

FenceMagnet

Personally I would go steel/steel as I can't see any advantage of mixing them if all ceramic isn't an option.

You could always email Paul and ask for his recommendation, cost...
Forum: Glow Engines
06-07-2005, 10:31 AM
Replies: 11
Views: 4,601
Posted By steveukflyer

RE: RC Engine Bearings

I too can report tha Paul offers first rate service and prices. I first used him a couple of years ago when I had rust problems with an ASP engine. They were cheaper than the chinese originals and...
Forum: Glow Engines
09-20-2004, 08:23 AM
Replies: 5
Views: 1,221
Posted By steveukflyer

RE: TT 46 pro carb question.

you are missing either a spring or a lock nut;)
Forum: Glow Engines
09-19-2004, 01:32 PM
Replies: 11
Views: 1,658
Posted By steveukflyer

RE: TT GP07 seems very tight

I had an sc12 the same. Heated it with my hot air gun for 5 minutes then hit it with the starter. When they are that tight (and they shouldn't be) you have to be very careful not to damage the con...
Forum: Glow Engines
09-19-2004, 01:14 PM
Replies: 2
Views: 579
Posted By steveukflyer

RE: Moki 2.10

My Moki 1.35 likes to be wet before it starts, if you have the engine inverted it could be that it doesn't have enough fuel in the crankcase when you try to start it. JoeAirPort's advice seems...
Forum: Glow Engines
09-19-2004, 01:02 PM
Replies: 58
Views: 5,626
Posted By steveukflyer

RE: ceramic bearings ?

Hi Ernie

See your pm's

Steve
Forum: Glow Engines
09-17-2004, 01:34 PM
Replies: 9
Views: 606
Posted By steveukflyer

RE: Meoca 61 pro & Side position

are you runniing exhaust pressure?
Forum: Glow Engines
09-16-2004, 04:38 PM
Replies: 58
Views: 5,626
Posted By steveukflyer

RE: ceramic bearings ?

I have ordered from Paul at rc-bearings.com numerous times and can recommend the bearings as totally fit for purpose. He also knows his stuff!!!. I have recently replaced the bearings in my ASP52s-...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.