RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: davealator
Showing results 1 to 14 of 14
Search took 0.59 seconds.
Forum: RC 1/8th Scale Buggies
03-01-2004, 08:47 AM
Replies: 10
Views: 739
Posted By davealator

RE: 1 way bearing, grease or no?

thanks Alex, i guess i'll pull it apart and clean it all out b4 it fails. thanks again for the info.
Forum: RC 1/8th Scale Buggies
02-27-2004, 10:15 PM
Replies: 10
Views: 739
Posted By davealator

RE: 1 way bearing, grease or no?

ok, Graham, i put just a little grease and worked it into the needle bearings, not crammed full to where it would clog, just enough, however, i am the 1'st to admit to being a fng, you obviously...
Forum: RC 1/8th Scale Buggies
02-26-2004, 04:50 PM
Replies: 10
Views: 739
Posted By davealator

1 way bearing, grease or no?

I removed the back plate of my new violator to loctite screws and discovered the 1 way and gears to be dry, i assumed the bearing would enjoy a little high temp grease, but I have since found...
Forum: RC 1/8th Scale Buggies
02-23-2004, 04:41 PM
Replies: 26
Views: 1,538
Posted By davealator

RE: A few new problems with the Violator.

Thanks, I also found the sticker kit and antennae tube under the cardboard in the box. I also disassembled the roto start to check the back plate and found one of the screws for the back plate...
Forum: RC 1/8th Scale Buggies
02-11-2004, 06:53 PM
Replies: 3
Views: 333
Posted By davealator

driveline preventative maintenance??

Other than main spur mesh, are there any other clearances, slop, binding, freeplay, etc. checks to avoid preventable premature expensive part replacement?:D
Forum: RC 1/8th Scale Buggies
02-09-2004, 01:07 PM
Replies: 10
Views: 456
Posted By davealator

RE: should i rebuild violator rtr?

just keeping thread alive
Forum: HPI Monster Truck Forum
02-08-2004, 09:48 AM
Replies: 5
Views: 388
Posted By davealator

RE: performance at end of run

do a search for header tank mod
Forum: RC 1/8th Scale Buggies
02-08-2004, 09:21 AM
Replies: 10
Views: 456
Posted By davealator

RE: should i rebuild violator rtr?

Especially preventable ones[>:]
Forum: RC 1/8th Scale Buggies
02-08-2004, 09:19 AM
Replies: 10
Views: 456
Posted By davealator

RE: should i rebuild violator rtr?

What about the diff's? and are there any other slop, mesh, freeplay, tightness, etc. checks in the drivetrain? again I don't like and can't afford expensive surprizes:D
Forum: RC 1/8th Scale Buggies
02-07-2004, 06:30 PM
Replies: 10
Views: 456
Posted By davealator

RE: should i rebuild violator rtr?

will gear mesh be obvious when i see it? and are you refering to max servo throw for steering and throttle-brake? if so, don't you check every time before you run?
Forum: RC 1/8th Scale Buggies
02-07-2004, 06:19 PM
Replies: 10
Views: 456
Posted By davealator

should i rebuild violator rtr?

I've recently purchased a Violator and was wondering if I should go through it b4 running. I have more time than money and don't like surprizes. If so, how far down should I go and what should I...
Forum: RC 1/8th Scale Buggies
02-07-2004, 05:59 PM
Replies: 9
Views: 817
Posted By davealator

RE: XTM Xterminator runaway... motor pics inside

did you have a fail safe? if not are you gettin 1?
Forum: RC 1/8th Scale Buggies
01-29-2004, 01:14 PM
Replies: 2
Views: 437
Posted By davealator

RE: FNG

320 brand new in factory sealed box, 20 shipping, can't wait
Forum: RC 1/8th Scale Buggies
01-28-2004, 08:09 PM
Replies: 2
Views: 437
Posted By davealator

FNG

Hello to all, I am the latest FNG. I ordered a Violator the other day off ebay 340 to the doorstep. Every night I haul it home, slide into the driveway, run to the front door like a little kid on...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.