RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ahff71
Showing results 1 to 15 of 15
Search took 0.59 seconds.
Forum: Marketplace
02-25-2023, 10:50 AM
Replies: 0
Views: 293
Posted By ahff71

Wanted-- Magnum xls cylinder head or engine

WANTED--Cylinder head or entire engine--Magnum xls 91.
Forum: Marketplace
07-08-2019, 06:08 PM
Replies: 1
Views: 858
Posted By ahff71

25% 78 inch Extra 260

Hanger 9 Extra 260
25%, 78 inch wingspan
Everything's there, just add receiver. $500 firm
Flies great. Some cosmetic flaws
Includes:
Desert Aircraft 50cc gas engine
Digital servos
...
Forum: NitroModels Support
07-12-2010, 09:28 PM
Replies: 3
Views: 767
Posted By ahff71

RE: Nitroplanes Yak 50cc landing gear

thanks. In fact, I went ahead and bent them and it worked well. But they still are heavy!!

Do you know of a specific make.model of cf gear that works for this plane?
Forum: NitroModels Support
04-23-2010, 01:28 PM
Replies: 3
Views: 767
Posted By ahff71

Nitroplanes Yak 50cc landing gear

The stock alum gear has very little ground clearance using a standart 50 cc 22" prop, plus they seem very heavy. Can anyone suggest an affordable alum or CF replacement that is both lighter and...
Forum: NitroModels Support
02-02-2010, 11:47 AM
Replies: 6
Views: 1,934
Posted By ahff71

RE: Yak 50cc CG? 85

Thanks for your reply.

Yes, what I'm trying to say as that the current, actual balance point is about an inch behind the 164mm suggested in the manual.

I'll take your advice and move the Rx...
Forum: NitroModels Support
02-01-2010, 11:29 PM
Replies: 6
Views: 1,934
Posted By ahff71

RE: Yak 50cc CG? 85

opjose, thanks for your reply.

some clarificationI tried to say at using the 164mm CG point indicated inthe manual, the plane balances very tailheavy.  I'd be afraid to fly it if indeed it's that...
Forum: NitroModels Support
01-31-2010, 02:35 PM
Replies: 6
Views: 1,934
Posted By ahff71

Yak 50cc CG? 85" nitroplanes

Where is the CG for a Nitroplanes Yak 50cc purchased in Nov., 2009? I've just completed building it with a DA50 and I am not confident the enclosed manual CG is correct.It balances quite...
Forum: 3D Flying!
07-29-2009, 11:18 AM
Replies: 0
Views: 763
Posted By ahff71

Fun Fly 3D Event, Fort Collins, CO

<div style="font-family: Arial; color: #000000; font-size: 12pt"><style type="text/css">p { margin: 0; }</style><div style="font-family: Arial; color: #000000; font-size: 12pt"><div...
Forum: Events, Shows and Fun Flys - Airplanes
07-29-2009, 11:13 AM
Replies: 0
Views: 1,038
Posted By ahff71

3D Fun Fly, Fort Collins, Colo.

<div style="font-family: Arial; color: #000000; font-size: 12pt"><style type="text/css">p { margin: 0; }</style><div style="font-family: Arial; color: #000000; font-size: 12pt"><div...
Forum: Esky Helicopters
11-14-2007, 02:58 PM
Replies: 2
Views: 778
Posted By ahff71

hbfp 4 in 1 problem

The 4 in 1 in my hbfp no longer activates the main motor. The servos and tail motor still operate. The main motor itself works, I connected it directly to a battery and it runs fine. My local...
Forum: ARF or RTF
10-07-2007, 03:40 PM
Replies: 1,604
Views: 282,777
Posted By ahff71

RE: Seagull Yak?

I'll look forward to hearing how it went.

I fly at LoveAir. I'm Andy
Forum: ARF or RTF
09-23-2007, 05:22 PM
Replies: 1,604
Views: 282,777
Posted By ahff71

RE: Seagull Yak?

Just found this thread--

Would a Saito 1.25 be enough for the Seagull Yak 90? Enough to hover and pull out vertically? I'm in Colorado at 5,000 ft. elevation.

On my Funtana 90, the 1.25...
Forum: 3D Flying!
07-30-2006, 04:21 PM
Replies: 3
Views: 578
Posted By ahff71

RE: H9 Extra 260 corkscrewing

good suggestions, guys. I'll check it out.

i was thinking perhaps it's just my thumb; that I'm pulling back and a bit to the right, 'tho I haven't had this problem while flying my other planes.
Forum: 3D Flying!
07-29-2006, 07:34 PM
Replies: 3
Views: 578
Posted By ahff71

H9 Extra 260 corkscrewing

I have about a dozen flights on my new H9 Extra 260 with DA50.

Whenever I use more than about 5-7 degrees of elevator, the plane corkscrews to the right. I've checked the movement of both...
Forum: 3D Flying!
07-02-2006, 02:37 PM
Replies: 3
Views: 491
Posted By ahff71

H9 260 motor?

I'm considering purchasing a H9 260. I'm at 5,000 ft. in colorado. Can't afford DA 50. Other recommendations...Saito 220, fuji43, glow 2-stroke, other??? Something that will allow sustained hover.
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.