RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: tucson
Showing results 1 to 10 of 10
Search took 0.03 seconds.
Forum: RC Jets
08-22-2020, 04:39 AM
Replies: 714
Views: 229,129
Posted By tucson

I cannot post a picture right now but yes I had...

I cannot post a picture right now but yes I had to add a 1/8 strip of hardwood to narrow the bearer. I used hysol then I glued a 3/32 piece of light ply to the bottom of the bearer which helped...
Forum: RC Jets
08-19-2020, 09:43 PM
Replies: 714
Views: 229,129
Posted By tucson

nose gear door

dave,
awfully large gaping hole where the nose wheel sits.
feels funny to look at it.
after you came out with your description to balance from the wing bolts mounting holes I tried it and removed...
Forum: RC Jets
08-19-2020, 05:23 PM
Replies: 714
Views: 229,129
Posted By tucson

Carf viper

I just finished upgrading my 3 year old carf viper to a set of electron electric gear.I have used the nose gear door prior to the upgrade. my question is how many of you have used or left the gear...
Forum: RC Jets
01-31-2020, 06:13 AM
Replies: 714
Views: 229,129
Posted By tucson

hi dave, as always thank you for your quick...

hi dave,
as always thank you for your quick reply.
stan
Forum: RC Jets
01-30-2020, 06:18 PM
Replies: 714
Views: 229,129
Posted By tucson

question on up grading to electric gear

gonzalo, I am thinking of upgrading my 3 year old comp arf viper to electric electron gear and brakes..
were you able to mount the nose gear and use a servo for direct steering eliminating the pull...
Forum: RC Jets
03-25-2017, 05:01 PM
Replies: 714
Views: 229,129
Posted By tucson

Peter I have been flying mine with a KT 210 and...

Peter I have been flying mine with a KT 210 and it is perfect. 5-6 min flights with almost 1/2 tank left.
The other day I was landing full flaps (80%) gear down didn't like how it looked over the...
Forum: RC Jets
04-30-2016, 10:06 AM
Replies: 714
Views: 229,129
Posted By tucson

I am finally happy with my KT engine install. I...

I am finally happy with my KT engine install. I removed a section of the carbon fiber below the engine as per the manual for additional cooling. That eliminated almost all of the tension for mounting...
Forum: RC Jets
04-30-2016, 06:04 AM
Replies: 714
Views: 229,129
Posted By tucson

I tried to send a picture but my cell phone takes...

I tried to send a picture but my cell phone takes pictures that are to large to send. New phone need to figure out how to change that:confused:
I do have to pull the sides in about 1/4 inch enough...
Forum: RC Jets
04-29-2016, 10:41 PM
Replies: 714
Views: 229,129
Posted By tucson

I have installed a KT210. I think I might have...

I have installed a KT210. I think I might have goofed during the install. I followed all the instructions I thought.
When I set the engine in the mount I discovered that when I centered the engine...
Forum: RC Jets
04-08-2016, 12:48 PM
Replies: 714
Views: 229,129
Posted By tucson

I just started my build on my Viper. I have all...

I just started my build on my Viper.
I have all HT 7955's. Looks like it will be interesting to get the 7955 into the stab.I am sure it can be done with enough patience or maybe not at all :-))
Has...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.