Jeti DS-24

Reply Subscribe

Thread Tools

Search this Thread

09-08-2018, 03:42 PM

#1051

leemkl06

Join Date: Aug 2013

Posts: 141

Likes: 0

Received 1 Like on 1 Post

Quote:

Originally Posted by rbgetz

Trying to make sure all my RX's have latest firmware using Jeti Studio. On one of my CB200's when I use the USB cable and plug into the EXT port on the CB200, I can't get it to read anything. no response. However, when i try another another CB200 to check firmware , it immediately connects and shows current version. Does anyone have any thought on why one CB200 has no response? i have all other cabling completely remove and no power to it.

THANKS.....

the CB200 needs to be powered to update (see manual). Just did two of mine today.

Reply Like

09-09-2018, 08:30 AM

#1052

gooseF22

Join Date: Aug 2006

Location: Fort Wayne, IN

Posts: 2,603

Likes: 11

Received 2 Likes on 2 Posts

Quote:

Originally Posted by JohnMac

So you have proved that the 900 mHz system works Paul. Why has someone installed a 2.4mHz jammer in the first place?
John

there is an additional backup tone emitted when it goes to 900 High in addition to signal lost. Look in the config

Reply Like

09-11-2018, 08:10 AM

#1053

skymaster68

My Feedback: (4)

Join Date: Sep 2003

Posts: 441

Likes: 36

Received 21 Likes on 19 Posts

New to Jeti

hello guys, i’m new to jeti and i have this quedtion, if anyone knows the answer I’ll really apresiate it...

I’m i stalling an R10 In a Carf Joker using a ds24 transmitter...
But i run out of channels, i cant connect my ecu

I have an R3 on hand...
How can I install the R3 to the R10 or how to bind both of them...
I remember I saw that some were but know I can’t find it...
I could get the channel for the electric gear out of the R3 and the rest from the R10...
Please let me know as soon as posible as I’m at the field trying to maiden my new Ds24

Thxs in advance
Brg

Slds
Cristian

Reply Like

09-11-2018, 08:13 AM

#1054

digitech

My Feedback: (10)

Join Date: Aug 2004

Location: klimmenlimburg, NETHERLANDS

Posts: 3,653

Likes: 2

Received 10 Likes on 10 Posts

Quote:

Originally Posted by skymaster68

where are you located?
Aeropanda in the usa sells a sb-exp 4 channel expander that works with jeti.
you connect it to a ex port and you can add more channels.

Reply Like

09-11-2018, 08:27 AM

#1055

skymaster68

My Feedback: (4)

Join Date: Sep 2003

Posts: 441

Likes: 36

Received 21 Likes on 19 Posts

Quote:

Originally Posted by digitech

where are you located?
Aeropanda in the usa sells a sb-exp 4 channel expander that works with jeti.
you connect it to a ex port and you can add more channels.

Unfortunatelly not in the US...

Can I use the R3 in clone Mode just for the the gear with a battery just for the R3? If so how to bind it...

Reply Like

09-11-2018, 08:37 AM

#1056

Dansy

My Feedback: (53)

Join Date: Mar 2002

Location: Prescott, Ont.

Posts: 2,992

Likes: 172

Received 160 Likes on 143 Posts

Frankly I wouldn’t do that, I used 12 ch’s in my smaller models or the cb200/400......

Reply Like

09-11-2018, 09:50 AM

#1057

LA jetguy

Join Date: Jan 2012

Location: Los Angeles, CA

Posts: 820

Likes: 35

Received 54 Likes on 42 Posts

Quote:

Originally Posted by skymaster68

If you use a "Cortex Pro" and setup the R10 in serial mode you can have the first 6 channels through Cortex Pro and re map others through R10 (in device explorer) to get a total of 16...

David

Reply Like

09-11-2018, 10:09 AM

#1058

Edgar Perez

My Feedback: (13)

Join Date: Dec 2001

Location: Gurabo, PUERTO RICO (USA)

Posts: 2,404

Likes: 4

Received 20 Likes on 10 Posts

Yes

I think you can run in dual path with both receivers connected to the DS24.
Then just map the channel you need to the R3.
That should work and no need to connect the Rx togheter.

Reply Like

09-11-2018, 10:56 AM

#1059

skymaster68

My Feedback: (4)

Join Date: Sep 2003

Posts: 441

Likes: 36

Received 21 Likes on 19 Posts

Quote:

Originally Posted by skymaster68

Unfortunatelly not in the US...

Can I use the R3 in clone Mode just for the the gear with a battery just for the R3? If so how to bind it...

Problem solved!!
NO BRAKES FOR TODAY

there was a strong head wind so no braking was necesay, I maiden my DS24 on my Joker that had an 18Mz before...
the handling of the 24 is supperb, I’m complity happy with it, now time to start migrating my other jets 😁
The red Joker looks cool aside the Custome Red Ds24!!

Reply Like

09-11-2018, 01:38 PM

#1060

skymaster68

My Feedback: (4)

Join Date: Sep 2003

Posts: 441

Likes: 36

Received 21 Likes on 19 Posts

Quote:

Originally Posted by LA jetguy

If you use a "Cortex Pro" and setup the R10 in serial mode you can have the first 6 channels through Cortex Pro and re map others through R10 (in device explorer) to get a total of 16...

David

Wow that's a good solution, yes I'm running a CP, will try that during the weekend, thxs for the advice..

Last edited by skymaster68; 09-11-2018 at 02:46 PM.

Reply Like

09-12-2018, 02:12 AM

#1061

JoeJr1485

Join Date: Dec 2015

Location: Germany

Posts: 470

Likes: 1

Received 0 Likes on 0 Posts

Hey all, so I have a question and I don’t know why I’m just now thinking of this. So I have a few turbines and as always I learn the TX to turbine and etc. but after looking in the TX I was drawing a brain fart, in my servo setup for throttle my max pos and neg limits are the default 125% so I went back and looked at all my turbine models and they are the same I never changed them. When setting up your turbines do you all limit both pos and neg to 100? Also I use a switch to set the trim full and off. The way I set the trim is in the function assignment set the switch used then set the trim-max to 100. Is that how you all do it?

Reply Like

09-12-2018, 04:04 AM

#1062

wfield0455

My Feedback: (7)

Join Date: Sep 2005

Location: Holliston, MA

Posts: 1,299

Likes: 1

Received 5 Likes on 4 Posts

Quote:

Originally Posted by JoeJr1485

There is no benefit to setting them above the default of 100% but as long as your ECU can handle the pulse width range and you have valid fail safe conditions set you can use any value you want . Since all my turbines had been previously setup on Spektrum which uses a throttle pulse width range of 1100us - 1900us, I simply reduced my end points to 80% to get that same range and then I didn't even need to repeat the teach RC process as the ECU had already learned that range. I simply use the Throttle cut and throttle idle functions to select stop/ idle. Since I use +/-80% end points I assign the Cut function to the stop position of my safety switch with a value of -125% and the idle function to the idle position of my 2 position safety switch with a value of 20%.

Reply Like

09-12-2018, 05:33 AM

#1063

JoeJr1485

Join Date: Dec 2015

Location: Germany

Posts: 470

Likes: 1

Received 0 Likes on 0 Posts

Quote:

Originally Posted by wfield0455

Thanks for the input. I made some changes to what you brief. I know there is a few ways to skin the cat with this transmitter but want to make sure that my logic and function to end state is as simple and safe as possible 😁

Reply Like

09-12-2018, 07:56 AM

#1064

causeitflies

Join Date: Jan 2003

Location: EASTERN OHIO

Posts: 2,437

Likes: 11

Received 42 Likes on 32 Posts

Quote:

Originally Posted by JoeJr1485

I set my kill switch to -100 (learned) and my failsafe to -125. That way if there is a failsafe the turbine ECU will recognize it as a failsafe as it is outside the learned programmed settings.

Last edited by causeitflies; 09-12-2018 at 07:58 AM.

Reply Like

09-12-2018, 09:07 AM

#1065

wfield0455

My Feedback: (7)

Join Date: Sep 2005

Location: Holliston, MA

Posts: 1,299

Likes: 1

Received 5 Likes on 4 Posts

Quote:

Originally Posted by causeitflies

I set my kill switch to -100 (learned) and my failsafe to -125. That way if there is a failsafe the turbine ECU will recognize it as a failsafe as it is outside the learned programmed settings.

Actually I was incorrect in my previous post. I double checked and I'm also using -100% for kill not -125% as I said earlier.

Reply Like

09-13-2018, 07:57 AM

#1066

F16Jeff

My Feedback: (11)

Join Date: Jul 2008

Location: Simi Valley, CA

Posts: 259

Likes: 8

Received 9 Likes on 8 Posts

Quote:

Originally Posted by gooseF22

Here is a quick video I did for Butterfly on a DS16.. watch it through first because I had to go back and get something I missed..
enjoy..
https://youtu.be/AKRKzGadPe0

https://youtu.be/EKkFwB36AeM

GooseF22,

Thank you for these videos. I was setting up my flaps using the flap switch. Getting them both set to move the same was a real pain. After watching these videos and implementing flaps with Butterfly, what a difference that made.

Again thank you for making flap setup a little easier.

Best regards, ,

Jeff

Reply Like

09-21-2018, 07:11 AM

#1067

Join Date: Jul 2004

Location: , FL

Posts: 354

Likes: 0

Received 10 Likes on 10 Posts

Something new has been added to the Jeti family. I think the scale jets can mostly benefit from this sensor.

Jeti Telemetry Sensor Hall Effect Magnetic ON/OFF Position

Our new Magnetic ON/OFF Position Sensor will allow you to trigger events based on the True/False signal sent to your Jeti receiver. This is especially important in applications like gear doors, Up and Go systems for sailplanes, and scale features like opening canopies or gear doors. You will install the magnet on the moving side of your opening and the sensor on the fixed side; allowing you to know when it is closed or open. This signal can then be used in logical switching to prevent accidents from occurring. Imagine a safety lockout that prevents your gear from raising/lowering unless the doors are opened first.

Zb/Jeti USA

Jeti Telemetry Sensor Hall Effect Magnetic ON/OFF Position

Click image for larger version

Name: jeti-hall-effect-position.jpg
Views: 223
Size: 66.3 KB
ID: 2262015

Click image for larger version

Name: jeti-hall-effect-position2n.jpg
Views: 282
Size: 8.7 KB
ID: 2262016

Click image for larger version

Name: jeti-hall-effect-position3n.jpg
Views: 293
Size: 9.0 KB
ID: 2262017

Reply Like

09-21-2018, 06:42 PM

#1068

ravill

Thread Starter

My Feedback: (11)

Join Date: Jan 2003

Location: Granite Bay, Ca

Posts: 5,704

Likes: 2

Received 90 Likes on 72 Posts

Ha!! WAY more important would be “3 green” letting us know all 3 gear are down, thus eliminating the “gear pass”!

Now THAT is pretty cool.

Reply Like

09-21-2018, 06:52 PM

#1069

causeitflies

Join Date: Jan 2003

Location: EASTERN OHIO

Posts: 2,437

Likes: 11

Received 42 Likes on 32 Posts

Quote:

Originally Posted by ravill

Ha!! WAY more important would be “3 green” letting us know all 3 gear are down, thus eliminating the “gear pass”!

Now THAT is pretty cool.

Gear down and gear up before the doors close. I've been trying to figure out where to put the magnet on the gear, not the door.

Reply Like

09-22-2018, 03:14 AM

#1070

tp777fo

My Feedback: (28)

Join Date: Feb 2002

Location: Greer, SC

Posts: 3,510

Likes: 56

Received 127 Likes on 88 Posts

Gpifp!

Reply Like

09-24-2018, 12:37 PM

#1071

warbird_1

My Feedback: (61)

Join Date: Feb 2002

Location: Perry,NY

Posts: 2,577

Likes: 0

Received 3 Likes on 3 Posts

not to change the subject ,but does anyone know how to set the transmitter to auto off" if it even has that feature" . i left mine on and drained the battery. lost about 2 hours of flying while it charged up. i know it has an alarm but i put the radio back in it's case and didn't hear it. thanks ,WB_1

Reply Like

09-28-2018, 02:20 PM

#1072

wfield0455

My Feedback: (7)

Join Date: Sep 2005

Location: Holliston, MA

Posts: 1,299

Likes: 1

Received 5 Likes on 4 Posts

Quote:

Originally Posted by paulhelis

hi i need help programming ds 24 with magnetic switch, centralbox 200, one 2.4 mhz rx and a 900 mhz rx i did binded both receivers but im not able to see central box and magnetic switch on the radio
i already changed serial link to xbus i cant find a video that shows how to do ir please help

I assume you bound the 2.4Ghz receiver in "default mode" since you are only using one. Connect the 2.4Ghz receiver to Rx1 and the 900Mhz receiver to Rx2 of the central box 200. The CB200 should show up as a subordinate to the 2.4Ghz receiver in Device explorer. The magnetic switch will never show up anywhere, it will simply power the CB200 on / off, nothing more.

Reply Like

10-18-2018, 03:06 AM

#1073

c_makhija

Join Date: Jun 2004

Location: , INDIA

Posts: 752

Likes: 0

Received 1 Like on 1 Post

Hi Guys,

Running the Sbec 30D with the DS24, while the unit performs flawless, it keeps disconnecting and reconnecting every few seconds in device explorer. Any idea what’s wrong?

Thanks
Chatty.

Reply Like

10-18-2018, 03:14 AM

#1074

Carsten Groen

Join Date: Nov 2004

Location: Denmark

Posts: 1,803

Likes: 7

Received 12 Likes on 9 Posts

Quote:

Originally Posted by c_makhija

Hi Guys,

Running the Sbec 30D with the DS24, while the unit performs flawless, it keeps disconnecting and reconnecting every few seconds in device explorer. Any idea what’s wrong?

Thanks
Chatty.

Yes, you need to update the firmware of the receiver to the newest version, well known problem with most of the Jeti receivers.

Reply Like

10-18-2018, 06:26 AM

#1075

c_makhija

Join Date: Jun 2004

Location: , INDIA

Posts: 752

Likes: 0

Received 1 Like on 1 Post

Maybe a stupid question, but the servos can remain connected right? While updating.
If not mistaken had updated the Rex 12 few months ago, unless there is another update.

Chatty.

Reply Like

Reply Share

First
Prev
43 / 85
Next
Last