RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Brettis1
Showing results 1 to 13 of 13
Search took 0.08 seconds.
Forum: Multi Rotor Helicopters
12-29-2013, 07:51 AM
Replies: 7
Views: 10,430
Posted By Brettis1

Try the thread in RC groups theres quite some...

Try the thread in RC groups theres quite some interest. I have a DX8 and it did everything as per book.Although I didn't read manual, I did troll through scores of youtube vids. I only picked mine up...
Forum: Gas Engines
07-15-2013, 09:02 AM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

Well I have run a few tanks through it on the trst stand and so far its purring at an idle and squeals like a cut cat when the throttle is tweaked.
I'm running castrol active 2T at 32:1 with 91...
Forum: Gas Engines
07-12-2013, 11:02 PM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

i take it that everyone doubles up with the muffler washers/spring washers as per diagram
Forum: Gas Engines
07-11-2013, 10:46 PM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35
Forum: Gas Engines
07-11-2013, 09:17 PM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

In the plastic bag containing the muffler there was a diagram of the screws and washer configuration. Apart form the translation saying they were gaskets the picture shows a doubling of them e.g. one...
Forum: Gas Engines
07-07-2013, 10:46 AM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

Ok,  thanks for that. it just seems that there is nothing in the cap  for the plug electrode to come into contact with.will try and see what happens.
Forum: Gas Engines
07-07-2013, 10:09 AM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

i'm just about ready to mount it in the test stand and I noticed in the spark plug cap there is a plastic insert and a spring and I cant see any way that the center contact will not come into contact...
Forum: Gas Engines
07-01-2013, 11:57 PM
Replies: 452
Views: 102,770
Posted By Brettis1

RE: New DLE 35

I have a new 35 RA. This is my entry into gassers. So whats the method of starting the very first time. Choke with a few turns of the prop  and then back off? what throttle settings ? just off idle?...
Forum: RC Gliders, Sailplanes and Slope Soaring
02-19-2013, 09:22 AM
Replies: 9
Views: 2,873
Posted By Brettis1

RE: The HobbyKing Ventus EPO PNF glider V2

so it is roughly 30mm back like they recommend.i also see they have rear mounted the motor which a PIA so looks like I'll have to split the fuse to remove it and then glue a front mount on.Might...
Forum: RC Gliders, Sailplanes and Slope Soaring
02-18-2013, 04:47 PM
Replies: 9
Views: 2,873
Posted By Brettis1

RE: The HobbyKing Ventus EPO PNF glider V2

I also have read it came out very nose heavy. was thinking of actually removing landing gear and servos and run some tape underneath as I have always had a grassed area to land. in saying that the...
Forum: RC Gliders, Sailplanes and Slope Soaring
02-18-2013, 12:54 PM
Replies: 9
Views: 2,873
Posted By Brettis1

RE: The HobbyKing Ventus EPO PNF glider V2

Do you think the servos are cooking because of the stiffness of the wings. i'm tempted to either CA some mylar hinges in or possiblt slice through the foam hinges maybe 50% lenth to see if that eases...
Forum: RC Gliders, Sailplanes and Slope Soaring
02-18-2013, 10:20 AM
Replies: 9
Views: 2,873
Posted By Brettis1

RE: The HobbyKing Ventus EPO PNF glider V2

Did you keep it stock standard or have made any mods. As mine came less control horns for the wings and the R/E ones arent that good I'm getting some better ones. I'm going to get some better...
Forum: RC Gliders, Sailplanes and Slope Soaring
02-15-2013, 02:29 PM
Replies: 9
Views: 2,873
Posted By Brettis1

The HobbyKing Ventus EPO PNF glider V2

anyone got one of these recently. just received mine
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.