RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Mark Burgess
Showing results 1 to 25 of 25
Search took 0.44 seconds.
Forum: Flybarless Helicopters
02-03-2012, 09:27 PM
Replies: 6
Views: 3,050
Posted By Mark Burgess

RE: Align T-Rex 550e V2 3GX setup

Sorry. The purple wire goes into channel 3 where the manual shows yellow should be. So all I did was swop the yellow with the purple.
Forum: Flybarless Helicopters
01-28-2012, 03:21 PM
Replies: 6
Views: 3,050
Posted By Mark Burgess

RE: Align T-Rex 550e V2 3GX setup

I found out what my problem was. I was following an incorrect manual. The picture in the Align Manual for the Futaba Rx is wrong. The yellow pitch wire goes into channel 6 (NOT 3 as shown)
Forum: Flybarless Helicopters
01-19-2012, 03:15 AM
Replies: 6
Views: 3,050
Posted By Mark Burgess

Align T-Rex 550e V2 3GX setup

Help please. I am using a Futaba 10CHP Tx and a R 617FS Rx with the HR3 swash selected.
I am in the initial stages of setting up the swashplate in the DIR setting on the 3GX system.
I cannot get...
Forum: Futaba Radios Direct support forum
01-17-2012, 11:52 PM
Replies: 1
Views: 1,656
Posted By Mark Burgess

Futaba 10c & Align 550 3gx setup

Help please. I am trying to setup my 10c and I am in the initial DIR setup mode on the Flybarless setup and trying to get my swashplate moving correctly. The problem is that I cant get any movment...
Forum: Futaba Radios Direct support forum
09-14-2008, 07:52 AM
Replies: 2
Views: 634
Posted By Mark Burgess

RE: radio glitches

I had similar problems also on a 7Chp. see www.3d-downunder.com/forum/viewtopic.php?f=35&t=910

www.rcuniverse.com/forum/m_6767368/tm.htm

I tried to get in the air for over a year trying...
Forum: Futaba Radios Direct support forum
08-08-2008, 05:19 AM
Replies: 4
Views: 824
Posted By Mark Burgess

RE: OK to use USA 2.4 gig radio in Australia

Selective hearing going on PlaneHeli ! I doubt you will get a constructive, positive, brand supportive answer.

More here www.rcgroups.com/forums/showthread.php?t=892270
Forum: Futaba Radios Direct support forum
07-13-2008, 07:58 PM
Replies: 8
Views: 1,345
Posted By Mark Burgess

RE: Dedicated FAAST 10C

Totally agree !!!
It's like strapping your spare wheel to the roof of your car - works just as good but looks really out of place.
Forum: Futaba Radios Direct support forum
06-11-2008, 07:34 AM
Replies: 1
Views: 669
Posted By Mark Burgess

R 6014FS Signal output

Bax
Please enlighten me. Are my Hitec Digitals (HS 5955 & HS5645's) going to work with this reciever or am I now in for a powerbox of sorts ? Are they going to get the 6 (expensive) volts going...
Forum: Futaba Radios Direct support forum
06-11-2008, 01:28 AM
Replies: 1
Views: 598
Posted By Mark Burgess

New 10C Aerial

Aerial
I have the new 10 on order (for a long time now)[&o] and I have a question.
Can the Aerial from the module be routed through the Aerial hole in the TX so it looks neater and not like an...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-17-2008, 03:37 AM
Replies: 18
Views: 1,574
Posted By Mark Burgess

RE: Calling All Kiwis - Importing RC Txs to NZ

I have a Futaba 10c 2.4 Ghz on my wish list at Tower Hobbies and look forward to their email to say they are ready to ship. I have been flying futaba for 30 years and have never had a TX pack up....
Forum: Futaba Radios Direct support forum
03-16-2008, 06:37 AM
Replies: 6
Views: 5,455
Posted By Mark Burgess

Futaba in Australia

[&o] Can someone tell me what's happening to Futaba in Australia.
I have been a Futaba user/flier for, must be, 30 years now. Firstly in South Africa and now in Australia.
I have been really...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
03-08-2008, 03:50 AM
Replies: 1
Views: 1,015
Posted By Mark Burgess

HS 5645mg & Interference

[&:]For the last few months I have been trying to solve an interference problem see….http://www.rcuniverse.com/forum/m_6767368/tm.htm
I think I have found the problem. Today I started from...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
01-22-2008, 01:21 AM
Replies: 47
Views: 3,516
Posted By Mark Burgess

RE: Mode 2 Flyers "UNITE"!

:DThere is only one way to fly.... are all full size planes configured wrong!
I am the only guy in my club who flies the correct way. Mode 2. I am badly out numbered and the reason is all our mode...
Forum: JR Radio & Spektrum Radios
01-20-2008, 02:36 AM
Replies: 2
Views: 1,312
Posted By Mark Burgess

Changing Modes

A club member is selling a JR Propo X2610 at a give away price. It's on Mode 1 [:@]
I fly mode 2 how easy is it to change. I had a quick look at the JR Propo X2610 manual but could not find...
Forum: Gas Engines
12-30-2007, 04:36 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

[:@]42 degrees C outside today so being 1 of 3 fools out at the field I setup the plane. Battled like crazy to get the motor started and between blinks of sweat noticed the fuel tube loop on the...
Forum: Gas Engines
12-24-2007, 01:52 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

It does, one of the first things I tried....

Mark
Forum: Gas Engines
12-24-2007, 12:28 AM
Replies: 43
Views: 4,368
Posted By Mark Burgess

RE: DL50 compression/starting

Here is what I do with my DL 50.
1. Ignition off, close the choke and put my finger over the carb openenig and flick the prop about 5 times or untill I can feel my finger is wet
2. Ignition on...
Forum: Gas Engines
12-24-2007, 12:16 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

I have tried 2 plugs and there was no change. Obviously I used the original plug that came with the motor. I also have tried a NGK CM-6. The NGK is not a resistor plug. Iv'e been told that the plug...
Forum: Gas Engines
12-23-2007, 05:38 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

The Edge is still grounded but there is light at the end on the tunnel !!

These are the changes I have made.

-The rudder cables have been separated by a plastic bar.
-The Ignition battery...
Forum: Gas Engines
12-21-2007, 12:54 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

I am in Loxton, South Australia.
The first thing I did was to move the arial as mine was actally touching the CF tail wheel. My RX is as far from the ignition module as possible, same as yours....
Forum: Gas Engines
12-20-2007, 01:57 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

Thanks for all the tips.

I'm gonna try a new PCM RX on the weekend plus check on all the advice you guys have given. I got a heap of good advice from Precision Aerobatics (the supplier of the...
Forum: Gas Engines
12-17-2007, 09:20 PM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

Check out the photos in my gallery. I have tried swopping the servos and no matter its always the rudder that glitches not specifically the rudder servo.

Thanks to all who are replying.

Mark
Forum: Gas Engines
12-17-2007, 03:29 PM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

Plug cap is on. I took the CF rudder arm off the servo and put on a stock plastic one and the servo gittered, all while the engine was running. I will check that the wires are not rubbing, but when I...
Forum: Gas Engines
12-17-2007, 02:47 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

RE: Glitches, help needed

It only happens when the engine is running. I get a good 50-60 pace range check with the motor off but only about 20 paces with the motor on.
Forum: Gas Engines
12-17-2007, 12:22 AM
Replies: 53
Views: 5,358
Posted By Mark Burgess

Glitches, help needed

Please can anyone help ? I am trying to setup a DL-50 in a PA Edge 540 and I am picking up glitches in my rudder servo (hitec 5955TG). I can only get about 20 paces in a range check with the motor...
Showing results 1 to 25 of 25


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.