1/2a War Bird Fun Fighters
#52
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
oh and for the record deodrant and aftershave make the plan/template sheet go transparent for about 5 mins till it dries out
#54
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
got none. its quite hard to buy that fdrom the shops over here. im going to have to face that il have to draw over the lines in pen then do it it i think
#55
My Feedback: (10)
RE: 1/2a War Bird Fun Fighters
whats the quickest way to transfere ink of a paper template to balsa!
#57
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
i dont own a pizza cutter. iv tried everything and it wont transfere going to try thiken the lines up on the toner see if it does it then
#58
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
iv figured it out, all you need is an iron with a steam funtion on it.
1. lay down the piece of wood you wish to porint on.
2. freshly print out the pattern sheet (not important but helps print to transfere)
3. cut all the formers out not keeping to the lines but cut well oversized.
4. lay down the first print you wish to transfere onto the dry wood
5. set the heat on your iron to almost full and set a low steam seting (the steam losens the ink for transfere)
6. put plenty oif pressure on the print out and work from one side to the other qappliying lots of pressure.
7. remove the template sheet and you should have a good pattern there if its faint run round it with a pencil.
will put photos up of my formers as soon as iv done them, oh one last thing print fresh patterns out for the oposit formers as once they have been heated up and so forth they wont do a second round.
1. lay down the piece of wood you wish to porint on.
2. freshly print out the pattern sheet (not important but helps print to transfere)
3. cut all the formers out not keeping to the lines but cut well oversized.
4. lay down the first print you wish to transfere onto the dry wood
5. set the heat on your iron to almost full and set a low steam seting (the steam losens the ink for transfere)
6. put plenty oif pressure on the print out and work from one side to the other qappliying lots of pressure.
7. remove the template sheet and you should have a good pattern there if its faint run round it with a pencil.
will put photos up of my formers as soon as iv done them, oh one last thing print fresh patterns out for the oposit formers as once they have been heated up and so forth they wont do a second round.
#59
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
heres a few pics, you cant see it well but when you see it infront of you the lines are perfect im not used to this new camera for close up shots.
#60
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
does anyone have the dimensions for a Cox 049 surestart, i need width height and length and also the average distance from bulkhead to back of prop. also are they any good runing inverted
#61
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
here we go 1-3 and 5-8 cut out just need to do the 4th formers as they were on too soft a balsa for my point of view. tip i founmd was to use the very point of your knife to cut them out and to cut the notches for the stringers out before you cut the whole former out
#64
RE: 1/2a War Bird Fun Fighters
Just iron templates over balsa, they will print on it.
Other way is use carbon paper between plans and a piece of hard paper ( carton maybe ? ) this way you ll save your plans for future planes.
hope it helps.
Rafa
Other way is use carbon paper between plans and a piece of hard paper ( carton maybe ? ) this way you ll save your plans for future planes.
hope it helps.
Rafa
#65
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
i already found that out early on today. cut most of the ribs out wont be long befopre i can start gluing
#66
RE: 1/2a War Bird Fun Fighters
ORIGINAL: sir crashallot
heres a few pics, you cant see it well but when you see it infront of you the lines are perfect im not used to this new camera for close up shots.
heres a few pics, you cant see it well but when you see it infront of you the lines are perfect im not used to this new camera for close up shots.
George
#67
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
i think it has, il have to get the instruction box out and read it up, they make things so complicated, give me a pentax camera with a 35mm film with a 200 exposure any day
#68
RE: 1/2a War Bird Fun Fighters
ORIGINAL: sir crashallot
i think it has, il have to get the instruction box out and read it up, they make things so complicated, give me a pentax camera with a 35mm film with a 200 exposure any day
i think it has, il have to get the instruction box out and read it up, they make things so complicated, give me a pentax camera with a 35mm film with a 200 exposure any day
I think when I got my first 35mm SLR (Petri Flex V) the ASA for Kodachrome was either 12 or 25 (perhaps the 25 was Ektachrome).
George
#69
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
dont get me wrong the digitals great stuff but you have to work for nasa and get a degree to be able to use it
my dads minolta was good too
my dads minolta was good too
#70
Senior Member
Thread Starter
Join Date: Sep 2008
Location: South Yorkshire, UNITED KINGDOM
Posts: 1,593
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/2a War Bird Fun Fighters
ORIGINAL: gcb
George
George
my first names george then its brent pickering my dad was called george too not a name you hear very often any more
#71
RE: 1/2a War Bird Fun Fighters
ORIGINAL: sir crashallot
my first names george then its brent pickering my dad was called george too not a name you hear very often any more
my first names george then its brent pickering my dad was called george too not a name you hear very often any more
George