will it ever work????
#1
Thread Starter
Junior Member
Joined: Jun 2008
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
From: mk, UNITED KINGDOM
hello i got a brand new smartech tiger 1:10 nitro and all it is it wont start i plug the glowstick in then pull the string and yeah i did put nitro stuff in I AM NEW please dont tell me all the complicated stuff other wise i wont know but when i try to pull it the string gets stuck and then you can hardly pull it why does this happen please help i only got it today and im dieing to have a go
#2
Senior Member
My Feedback: (1)
Joined: Mar 2008
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
From: Bel Air, MD
Since it's brand new you need to break the motor in. (look in your manual which should tell you the recomended procedure) wats happening is the piston is getting lock from too much pressure and stuff. just take the glow plug out with a nut driver, let the fuel get out by pulling the chord a couple times and for a while, spray wd-40 in the engine and pull on the chord for pretty good long time to help wear it in a bit. then put the glow plug back in and try again, repeat if needed.
#3
Senior Member
Joined: Nov 2007
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
From: Richmond Hill,
NY
if your pull start is hard to pull your engine is flooded (too many fuel inside the engine)
is your glowstick charger?
check if your glow plug is glowing
is your glowstick charger?
check if your glow plug is glowing
#4
Thread Starter
Junior Member
Joined: Jun 2008
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
From: mk, UNITED KINGDOM
right thanks for all that but now i got worse problems the pull string snapped of is easy to fix if it is and how do you fix it it?? looks like im not ment to have these sort of cars am i
#5
Senior Member
Joined: Nov 2007
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
From: Richmond Hill,
NY
take a look at these
http://youtube.com/watch?v=K1_Y2ukDp4M
http://youtube.com/watch?v=pAggkhHqEkw
http://youtube.com/user/Squirrelod
these think happen when you are a beginner and you dont know any thing
you just have to learn
their is a lot of thing you have to know in the hobby
http://youtube.com/watch?v=K1_Y2ukDp4M
http://youtube.com/watch?v=pAggkhHqEkw
http://youtube.com/user/Squirrelod
these think happen when you are a beginner and you dont know any thing
you just have to learn
their is a lot of thing you have to know in the hobby
#6
Thread Starter
Junior Member
Joined: Jun 2008
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
From: mk, UNITED KINGDOM
the video helped thanks but now it wont start you can hear it trying to start because it sarts for half a second does anyone have some tips?
#7
communicating here is too slow and frustrating for you and us, go the the lhs or find a friend who has done this before. trying to explain the basics is the hardest part, the complicated stuff is easy.
#8
Senior Member
Joined: May 2008
Posts: 202
Likes: 0
Received 0 Likes
on
0 Posts
From: Miami,
FL
I think your problem is that your either priming the engine so much that your flooding it or not enough that it can't stay running. Three words: READ THE MANUAL.



[8D]
